Manualsbrain.com
  1. Инструкции и руководства
  2. Бренды
  3. Panasonic
  4. cq-c1300an
  5. Справочник Пользователя

Справочник Пользователя для Panasonic cq-c1300an

Скачать
Страница из 19
37
CQ-C1400N/1300AN/1300GN
28
E
N
G
L
I
S
H
36
CQ-C1400N/1300AN/1300GN
27
E
N
G
L
I
S
H
Troubleshooting  
(continued)
There is little difference in receiving conditions between the current station
and AF stations. Update of AF list ended in failure.
a
Wait until AF list is successfully updated. For unstable reception, tune
into a stable station by hand.
An AF station cannot
be received even if
EON is set to ON.
The unit received a station that broadcasting time that is not appropriate for
you, or the unit is receiving a station that does not broadcast time.
a
Receive a station that broadcasting time that is appropriate for your
area, or adjust CT manually.
The clock (CT) does
not indicate accurate
time.
Any specified PTY programs cannot be received. There is no desired program
being broadcast in your area.
a
Select another PTY, or wait until a desired program starts.
“NO PTY”  appears
when selecting PTY.
When the station changed between programs, the unit could not receive the
PTY code.
a
An appropriate program is searched for and tuned into after receiving a
corresponding PTY code. Therefore, wait for a while.
Receiving programs
differs from PTY that
was already set up. 
A PS code cannot be received for the reason of bad receiving conditions, etc.
a
A PS code appears if it is received. Wait for a while until conditions
change. 
PS does not appear
even if an RDS station
is tuned into. (“NONE”
appears.)
Problem
Possible cause
a
Possible solution
■
CD
A label is peeled off from the CD in the unit.
a
Refer repair to the dealer where you purchased the unit.
The microcontroller in the unit operates abnormally due to noise or other fac-
tors.
a
Press the reset switch. If there is no reset switch, unplug the power cord
and plug it again. In case the unit is still out of order, consult the dealer. 
Disc unejectable
The unit is not sufficiently secured.
a
Secure the unit to the console box with the rear support strap, etc.
The unit is tilted at over 30˚ in the front-to-end direction.
a
Make the angle 30˚ or less.
Sound skipping due to
vibration 
There is a flaw or foreign material on the disc.
a
Remove the foreign material, or use a flawless disc. 
Sound skipping or
noise
The disc is inserted upside down.
a
Insert a disc correctly.
There is a flaw or foreign material on the disc.
a
Remove the foreign material, or use a flawless disc.
No playback or disc
ejected
Problem
Possible cause
a
Possible solution
■
RDS
■
MP3/WMA
There is a flaw or foreign material on the disc.
a
Remove the foreign material, or use a flawless disc. For MP3/WMA,
refer to the description about MP3/WMA.
Sound skipping or
noise
The playability of some CD-R/RWs may depend on the combination of media,
recording software and recorder to be used even if these CD-R/RWs are
playable on other devices such as a PC.
a
Make CD-R/RWs in different combination of media, recording software
and recorder after referring to the description about MP3/WMA.
The CD-R/RWs that are
playable on other
devices are not
playable on this unit.
The disc has unplayable formatted data.
a
Refer to the description about MP3/WMA for playable sound data except
CD-DA (i.e. music CD).
The unit plays back the first track of a MIX mode CD.
a
Skip the first track.
No playback or disc
ejected
Problem
Possible cause
a
Possible solution
Note:
¡
Refer to “Notes on MP3/WMA”. (
a
Page 26)