Справочник Пользователя для JVC GR-D20

EN

The audio track can be customized only when recorded
in the 12-bit mode (

墌

 pg. 21).

● Audio Dubbing is not possible on a tape recorded in

16-bit audio, on a tape recorded in the LP mode or on a
blank portion of a tape.

● To perform Audio Dubbing while watching on the

television, make connections (

墌

 pg. 15).

Play back the tape to locate the point where editing

will start, then press PAUSE (6) 

T

.

While holding A.DUB (e) 

j

 on the remote control,

press PAUSE (6) 

T

. “6e” 

y

 and “MIC” (GR-D50/D30

only) appear.

Press PLAY (4) 

h

, then begin “narrating”.

Speak into the microphone.

• To pause dubbing, press PAUSE (6) 

T

.

To end Audio Dubbing, press PAUSE (6) 

T

, then

STOP (5) 

O

.

..... set “12BIT MODE” to “SOUND 2” or “MIX” in the

Menu Screen (

墌

 pg. 25).

● Sound is not heard from the speaker during Audio

Dubbing.

● When editing onto a tape that was recorded at 12-bit, the

old and new soundtracks are recorded separately.

● If you dub onto a blank space on the tape, the sound may

be disrupted. Make sure you only edit recorded areas.

● If feedback or howling occurs during TV playback, move

the camcorder’s microphone away from the TV, or turn
down the TV’s volume.

● If you change from 12-bit to 16-bit in mid-recording and

then use the tape for Audio Dubbing, it is not effective
from the point where 16-bit recording began.

● During Audio Dubbing, when the tape moves to scenes

recorded in the LP mode, scenes recorded in 16-bit audio
or a blank portion, Audio Dubbing stops (

墌

 pg. 44).

● To perform Audio Dubbing with a video unit connected to

the camcorder’s AV connector, first set “S/AV INPUT” to
“ON” in the Menu Screen (GR-D50/D30 only, 

墌

 pg. 24).

“AUX” appears instead of  “MIC”.

You can record a new scene into a previously recorded
tape, replacing a section of the original recording with
minimal picture distortion at the in and outpoints. The
original audio remains unchanged.

● Before performing the following steps, make sure that

“TIME CODE” is set to “ON” in the Menu Screen
(

墌

 pg. 24, 25).

● Insert Editing is not possible on a tape recorded in the LP

mode or on a blank portion of a tape.

● To perform Insert Editing while watching in the television,

make connections (

墌

 pg. 15).

Play back the tape, locate the Edit-Out point and

press PAUSE (6) 

T

. Confirm the time code at this

point (

墌

 pg. 24, 25).

Press REW (2) 

U

 until the Edit-In point is located,

then press PAUSE (6) 

T

.

Press and hold INSERT (w) 

I

 on the remote

control, then press PAUSE (6) 

T

. “6w” 

&

 and the

Time Code (min.:sec.) appear and the camcorder
enters Insert-Pause mode.

Press START/STOP 

a

 to begin editing.

• Confirm the insert at the time code you checked in

step 1.

• To pause editing, press START/STOP 

a

. Press it

again to resume editing.

To end Insert Editing, press START/STOP 

a

, then

STOP (5) 

O

.

● Programme AE with special effects (

墌

 pg. 16) can be

used to spice up the scenes being edited during Insert
Editing.

● During Insert Editing, the date and time information

changes.

● If you perform Insert Editing onto a blank space on the

tape, the audio and video may be disrupted. Make sure
you only edit recorded areas.

● During Insert Editing, when the tape moves to scenes

recorded in the LP mode or a blank portion, Insert Editing
stops (

墌

 pg. 44).

9

0

2

3

4

6

w

e

5

W

E

U

R

I

Y

k

g

f

T

O

P

d

s

j

l

;

a

h

  01 D50/40/30/20EK 28-33

02.12.4, 19:12

29