Справочник Пользователя для Electrolux full size tumble action washer
4
11. From the rear of the washer, carefully pull out the power
supply cord through the hole in the backsheet.
12.Replace the service panel and screws.
NOTE:
If the washer is to be transported at a later
date, the shipping support hardware must be
reinstalled to prevent shipping damage.
date, the shipping support hardware must be
reinstalled to prevent shipping damage.
BOLT
SPACER
"P" CLAMP
IMPORTANT
MINIMUM INSTALLATION CLEARANCES
When installed in alcove: Sides, Rear, Top = 0 in
(0 cm).
When installed in closet: Sides, Rear, Top = 0 in
(0 cm), Front = 1 in (2.54 cm).
Closet door ventilation openings required: 2 louvers each 60 in
MINIMUM INSTALLATION CLEARANCES
When installed in alcove: Sides, Rear, Top = 0 in
(0 cm).
When installed in closet: Sides, Rear, Top = 0 in
(0 cm), Front = 1 in (2.54 cm).
Closet door ventilation openings required: 2 louvers each 60 in
2
(387 cm
2
) - 3 in (7.6 cm) from top and bottom of door.
UNPACKING
1. Cut the shipping carton along the dotted line along the base of
the unit.
2. While in the carton carefully lay the washer on its back side.
3. Remove the styrofoam base.
4. Carefully return the washer to an upright position and remove
the carton.
5. Carefully move the washer to within 4 feet (122cm) of the
final location.
6. Remove the following
from the back side
of the washer:
3 bolts,
3 yellow
plastic spacers,
2 or 3 metal
"P" clamps.
the unit.
2. While in the carton carefully lay the washer on its back side.
3. Remove the styrofoam base.
4. Carefully return the washer to an upright position and remove
the carton.
5. Carefully move the washer to within 4 feet (122cm) of the
final location.
6. Remove the following
from the back side
of the washer:
3 bolts,
3 yellow
plastic spacers,
2 or 3 metal
"P" clamps.
7. Remove the service panel from the front of the washer.
8. Remove the 4 nuts and 6 large washers that attach the 2
8. Remove the 4 nuts and 6 large washers that attach the 2
yellow shipping braces to the drum and the base. Lift up on
the drum and remove the braces (a yellow ribbon surrounds
the items to be removed). These braces must be removed to
allow the power supply cord to be released from the shipping
ring.
the drum and remove the braces (a yellow ribbon surrounds
the items to be removed). These braces must be removed to
allow the power supply cord to be released from the shipping
ring.
9. Remove the large styrofoam block
located under the drum. Lift up
on the drum, tilt the base of
the foam block inwards
toward the rear of the
washer until free, then
pull it out.
on the drum, tilt the base of
the foam block inwards
toward the rear of the
washer until free, then
pull it out.
10. Remove and discard
the yellow ribbon
and label from
the front of the
washer.
and label from
the front of the
washer.
ROUGH-IN DIMENSIONS
>
(43.2)
17
<
Ò
Ñ
8
4
3/8
<
>
v
^
(20.4)
(11.2)
LOCATION OF YOUR WASHER
DO NOT INSTALL YOUR WASHER:
1.
1.
In an area exposed to dripping water or outside weather conditions. The ambient
temperature should never be below 60 degrees F (15.6 degrees C) for proper
washer operation.
temperature should never be below 60 degrees F (15.6 degrees C) for proper
washer operation.
2.
In an area where it will come in contact with curtains or drapes.
3.
In an area (garage or garage-type building) where gasoline of other flammables are
kept or stored (including automobiles).
kept or stored (including automobiles).
4.
On carpet. Floor MUST be solid with a maximum slope of 1/2 in. per foot (1.27 cm
per 30.5 cm). To ensure vibration or movement does not occur, reinforcement of
the floor may be necessary.
per 30.5 cm). To ensure vibration or movement does not occur, reinforcement of
the floor may be necessary.