Справочник Пользователя для Andis Company men's shaver

connector fork “seats” itself on the inside
“point” on the nylon bracket. Push upper
blade slightly to opposite side of bracket on
the connector fork. Place lower blade on top
of the upper blade and align the screw holes
of blade to blade pad (see Diagram H) and
replace screws. Do not tighten down screws
completely. Turn clipper over and align lower
blade so teeth of both blades are parallel but
with lower blade teeth slightly above the
upper blade teeth (see Diagram I). Failure to
do this may result in nipping the skin of
your customer when cutting 
the hair.

ATTACHING THE CLIPPER COMBS
(Not always included with purchase of clipper)

The clipper comb blade attachments
mount easily. Just snap them on.
Snap them off. Combs help guide
hair to cutting blades and give you
precise control of hair lengths. Each
comb allows a different length of cut
which is indicated on the combs:
1/16", 1/8", 1/4", 3/8", 1/2", 3/4" & 1".
You can always set the blades for a
coarser cut by attaching any of the
snap-on blade attachments made for
your Andis Clipper/Trimmer.

To use blade attachment, slip the
cutter blade teeth into blade attach-
ment. Snap the blade attachment
down, they snap on and off easily. These attachments guide hair
into the clipper blades and give you precise control of hair
lengths. The length of trim is indicated on the blade attachment:
1/16", 1/8", 1/4", 3/8", 1/2", 3/4" & 1". Use the following chart to
find the approximate lengths of cut. Different blade angles in rela-
tion to the skin, thickness and texture of the hair will vary the cut-
ting length.

Your Andis Adjustable Clipper Blade
set is easy to adjust. From coarse to
fine cuts, all that’s needed is a flick of
the adjustment lever with your thumb.
In the upright position, blades are set
for the finest, or shortest cuts.

Form #12202 Rev. Q      

©2003 Andis Company, USA                          Printed in USA

This Andis product is warranted against defective material or workmanship for
one year from the date of purchase. All implied warranties arising and by virtue
of State law shall also be limited to one year. Any Andis product determined to
be defective in material or workmanship during the warranty period will be
repaired or replaced without cost to the consumer for parts and labor. The defec-
tive product must be returned with proof of purchase and $6.50 to cover cost of
handling, to any Authorized Andis Repair Station or to: Andis, 1800 Renaissance
Blvd, Sturtevant,  Wisconsin 53177 USA or IN CANADA to: A & AG AGENCIES
(CANADA), INC. 10050 Côte de Liesse, Lachine, Québec, H8T 1A3 CANADA.
Enclose or attach a letter describing the nature of the problem. Due to foreign
matter sometimes found in hair, clipper blades, or resharpening of blades, are
not subject to the one year warranty. Andis will not be liable under this warranty
for any defect, failure or malfunction of any of its products caused by normal
wear, abuse, misuse, unauthorized adjustments or dissembling. Andis will not be
liable for any consequential damages resulting from any defect in material or
workmanship of any of its products. Some States do not allow limitations on
how long an implied warranty lasts or exclusion or limitation of incidental or con-
sequential damages, so the above limitations or exclusions may not apply to you.
The Warranty gives you specific legal rights, and you may also have other rights
which may vary from State to State.

Date Purchased   ___________________________ Model ______________

Congratulations –

You just went First Class when you bought this

Andis Product. Careful workmanship and quality

design have been the hallmarks of Andis products

since 1922.

Diagram H

Diagram I

Position

000

•

•

•

1

ON EDGE

.030

.060

.090

.150

.180

FLAT

.030

.040

.050

.060

.080

When the blades of your Andis clipper/trimmer become dull after
repeated use, it is advised to purchase a new set of blades avail-
able through your Andis Supplier or through an Andis Authorized
Repair Station listed in this manual. (On Models ML, & SM, only
blade sets can be resharpened by an Authorized Andis Repair
Service Station. Please check the blades for missing teeth, as this
is considered a broken blade and not resharpenable). If you wish
your clipper/trimmer to be serviced as well, it should be carefully
packed and mailed either Parcel Post Insured, or U.P.S. to any of
the Service Centers listed in this manual.

Standard Andis Blade

With hair grain

1/16" 

to 

3/16"

Against hair grain

1/32"

to 

1/8"

1/16" Blade Attachment

With hair grain

3/16" 

to 

5/16"

Against hair grain

3/32"

to 

5/32"

1/8" Blade Attachment

With hair grain

1/4" 

to 

3/8"

Against hair grain

1/8"

to 

1/4"

1/4" Blade Attachment

With hair grain

3/8" 

to 

1/2"

Against hair grain

1/4"

to 

3/8"

3/8" Blade Attachment

With hair grain

1/2" 

to 

5/8"

Against hair grain

3/8"

to 

1/2"

1/2" Blade Attachment

With hair grain

5/8" 

to 

7/8"

Against hair grain

1/2"

to 

5/8"

3/4" Blade Attachment

With hair grain

7/8" 

to 

1-1/8"

Against hair grain

3/4"

to 

1"

1" Blade Attachment

With hair grain

1-1/8" 

to 

1-3/8"

Against hair grain

1"

to 

1-1/4"

Please see enclosed slip sheet 

for all Andis Authorized repair stations