Справочник Пользователя для Southwestern Bell gh3060
a. When the battery gets low, there will
be a low-battery beep
every 10 seconds . The handset will
display "BATTERY LOW" on the bottom
line.
b. If the battery becomes low while you are
using, you will be disconnected after about
1 minute. Terminate the call quickly and
put the handset in the base to recharge the
battery.
C. The battery will hold its charge for
several days out of the cradle, depending
on use.
be a low-battery beep
every 10 seconds . The handset will
display "BATTERY LOW" on the bottom
line.
b. If the battery becomes low while you are
using, you will be disconnected after about
1 minute. Terminate the call quickly and
put the handset in the base to recharge the
battery.
C. The battery will hold its charge for
several days out of the cradle, depending
on use.
Note:
from the handset
Installation
Before installing your phone, check the shipping carton to be sure you have
the following:
the following:
a. Keep the shipping carton and packaging, in case you need to transport your phone.
b. If there is visible damage, do not use this equipment. Contact your shipping agent
or return the telephone to the place of purchase.
b. If there is visible damage, do not use this equipment. Contact your shipping agent
or return the telephone to the place of purchase.
Box Contents
Notes:
1. Make sure DC adaptor is unplugged
from electrical outlet.
2. On the bottom of the base, press on
the tab (toward the battery compartment
door), and then lift the door away from
the unit.
3. Install one 9 volt battery.
4. Replace battery compartment door.
5. Install a replacement battery once a year
to ensure proper operation of the power
from electrical outlet.
2. On the bottom of the base, press on
the tab (toward the battery compartment
door), and then lift the door away from
the unit.
3. Install one 9 volt battery.
4. Replace battery compartment door.
5. Install a replacement battery once a year
to ensure proper operation of the power
Preliminary Preparation
Telephone Line Installation
Telephone Line Installation
Modular Outlet
1. Never install telephone jack during a
lightning storm.
2. Never install telephone jack in wet
locations unless the jack is specifically
designed for wet locations.
3. Never touch uninsulated telephone wires
or terminals unless the telephone line has
been disconnected at the network interface.
4. Use caution when installing or
modifying telephone lines.
lightning storm.
2. Never install telephone jack in wet
locations unless the jack is specifically
designed for wet locations.
3. Never touch uninsulated telephone wires
or terminals unless the telephone line has
been disconnected at the network interface.
4. Use caution when installing or
modifying telephone lines.
from a standard 110/120 volt outlet. The
handset is powered by a rechargeable
battery pack. Batteries are charged
automatically when the handset is placed in
the cradle of the base unit.
handset is powered by a rechargeable
battery pack. Batteries are charged
automatically when the handset is placed in
the cradle of the base unit.
Battery Backup
NOTE:
Installation (Cont.)
Table/Desk Installation
A. Plug one end of the long telephone line
cord into the back of the unit and connect
the other end to a modular wall jack. Press
until locking lever clicks (Fig. 1).
cord into the back of the unit and connect
the other end to a modular wall jack. Press
until locking lever clicks (Fig. 1).
C. Connect the DC Adaptor into the back
of the unit. Plug the other end into a
standard 110/120 volt outlet (Fig. 1).
of the unit. Plug the other end into a
standard 110/120 volt outlet (Fig. 1).
Fig. 1
BATTERY PACK MUST BE
CHARGED FOR 10-14 HOURS
BEFORE INITIAL OPERATION.
BEFORE INITIAL OPERATION.
DC adaptor
Line cord
Base Unit
Quick Installation Guide
Long Telephone Line Cord
DC Adaptor with Cord
Owner's Manual
Handset with Rechargeable Battery
The GH3060 Cordless Telephone operates
One 9 volt battery (not included) is required
to maintain clock and alarm time, and memory
settings during a power failure. If there is a
power failure and the battery is not installed,
clock and alarm time, and memory settings will
be lost.
to maintain clock and alarm time, and memory
settings during a power failure. If there is a
power failure and the battery is not installed,
clock and alarm time, and memory settings will
be lost.
failure protection feature. BATTERY LOW
icon will turn on until a 9 Volt battery is
installed. Your unit is fully functional. Battery
is needed for power failure backup ONLY.
icon will turn on until a 9 Volt battery is
installed. Your unit is fully functional. Battery
is needed for power failure backup ONLY.
D. Place the handset into the base. The
handset will beep .
handset will beep .
Handset Battery Charging
leave the handset in the base cradle for ten
After connecting the unit to DC power,
to fourteen hours before using it for the
first time. The CHARGE LED on the base
will be lit when the handset is in the cradle.
Later, it will take less time for the battery
to recharge.
first time. The CHARGE LED on the base
will be lit when the handset is in the cradle.
Later, it will take less time for the battery
to recharge.
9
10
T/P
RINGER
ON/OFF
DC10V 650mA
USE ONLY WITH CLASS 2 POWER SOURCE
-
+
The battery pack in the handset must be fully
charged for about 10-14 hours before using
the telephone. The Radio may be used prior
to the handset being fully charged. An
extension telephone will be required until the
handset is charged.
charged for about 10-14 hours before using
the telephone. The Radio may be used prior
to the handset being fully charged. An
extension telephone will be required until the
handset is charged.
BACKLIGHT
BRIGHT / NORMAL / OFF
SET
SNOOZE
1
2
ALARM
HANDS ET IN
THE BAS E
FACE DOWN
THE BAS E
FACE DOWN
CHARGE
SPEAKER
B. Connect the AM look antenna into the back
the unit (Fig.1). Place it on the desk or mount it
on the wall (Fig.2).
the unit (Fig.1). Place it on the desk or mount it
on the wall (Fig.2).
AM antenna
Fig.2