Справочник Пользователя для Plantronics CS60

• Lower the listen volume on your softphone until

the distortion disappears.

• If the distortion is still present, lower the listen

volume control on the computer.

• Adjust volume on headset. See page 12.

• Speak volume is too high. Lower the speak volume

on your softphone until the noise disappears. If the

noise is still present, lower the microphone volume

control on the computer.

• Link to headset is lost. Try to re-establish a link by

pressing the call control button.

• Unplug the USB charger first, then unplug the AC

charger (if used) from the base for 5 seconds. Plug

the USB charger back in first, then AC adapter (if

used) to power back up.

• Reset the whole system as described on page 18.

• Move the CS60-USB base further away from your

phone.

• AC charger is plugged into a power strip. Plug the

AC charger into the wall directly.

• The CS60-USB will set itself as the default audio

device in Windows

. Use the Audio settings in

Windows

under Sounds and Audio Devices to

change the device used for audio.

• Headset may require reset. See page 18.
• Headset battery needs to be charged. See page 7.
• If you are using a laptop that regularly goes into

standby or hibernation, the optional AC power

supply is provided to ensure the headset can be

continuously charged.

• Battery is deteriorating; replace the battery with a

new battery pack. See page 19.

• Try changing earloop sizes. Experiment to find the

best fit or use the over-the-head band supplied.

• One beep every 10 seconds is caused by a low battery

warning. Recharge battery by returning headset to

the base charging cradle for one to three hours until

charge light stays lit or stops blinking.

• Two beeps is an out of range warning. Move closer

to the base.

• Three beeps every 15 seconds indicate your mute is

on. Press the mute button once to turn mute off.

Sound in headset is distorted.

I can hear echo in headset.

I can hear too much background
conversation or noise.

I hear static that does not allow

me to communicate.

People I talk to can hear a buzz
in the background.

The other headset I was using
to listen to music does not work
any more.

My headset stops responding
to button presses.

Battery talk time performance
is significantly degraded even
after a full charge.

Headset is uncomfortable when
worn in over-the-ear mode.

I hear beeps in the headset.

Problem

Solution

TROUBLESHOOTING FOR CS60-USB

• Headset may be out of range of the base. Move closer

to base unit until the headset is within range. Range

varies with office environment.

• Headset battery needs to be charged. See page 7.

If you are using a laptop that regularly goes into

standby or hibernation, the optional AC power

supply is provided to ensure the headset can be

continuously charged.

• Listening volume is too low. Press the volume up

button on the headset. See page 12.

• You may have to re-subscribe your headset with the

base. See page 18.

• Check compatibility list on www.plantronics.com/

SoftphoneCompatibility to ensure your softphone is

compatible for remote answer and disconnect.

• Headset battery needs to be charged. If you are

using a laptop that regularly goes into standby or

hibernation, the AC power supply is available to

ensure the headset can be continuously charged.

• CS60-USB may not be set as the default audio device

in your softphone application.

• Check that all cords are connected correctly.
• Check that the base has power (green indicator light)

and the headset battery is fully charged.

• Headset may be out of range of the base. Move

closer to base unit until the headset is within range.

Range varies with office environment.

• Adjust the listen volume on the headset (see page 12),

softphone and PC audio control.

• Ensure the headset speaker is positioned snugly

over your ear.

• Incorrect softphone model selected. Ensure you

have selected the correct softphone model through

the software.

• You may need to re-subscribe the headset.

See page 18.

• Headset is muted. Press the mute button on headset

to unmute the microphone. See page 12.

• Headset microphone boom aligned incorrectly.

Align the headset boom with your mouth.

• Speak volume is too low. Increase the speak volume

on your softphone until you can be heard by callers.

If the volume is still too low, increase the microphone

level on your computer.

• Headset battery needs to be charged. See page 7.

My headset does not work with

the base unit.

My headset does not work with
my softphone.

I cannot hear caller.

Callers cannot hear me.

Problem

Solution