Справочник Пользователя для ICX Global arc moto 41
User’s Guide for the
4-in-1 Cable TV Remote Control
for Motorola
®
DCT Set-Top Boxes
Use this guide in conjunction with your cable
set-top box manual
© 2005 ICX Global, Inc.
All rights reserved
Part Number ICX 18351, version 2.0
02102005
Please plug your television power cord
into a separate wall outlet instead of the
power outlet on the cable box.
into a separate wall outlet instead of the
power outlet on the cable box.
Tune your television to channel 2, 3 or 4
as directed by your cable provider.
as directed by your cable provider.
!
Use only
new AAA Alkaline
batteries
to insure consistent
operation.
Two AAA alkaline batteries must be
installed before you can program or
operate the remote control.
installed before you can program or
operate the remote control.
1
. Remove the battery compartment cover
located on the back of the remote control.
2. Place the batteries in the compartment
in positions matching the picture below.
in positions matching the picture below.
3.
Replace the battery compartment cover.
IMPORTANT
NOTE
4
Know Your Remote
PAGE
#
PPV key allows
quick access to the
Pay Per View features
EXIT exits out of on-screen
menus
OK chooses the high-
lighted item in the menu
FOUR-WAY CURSOR KEYS
allow you to navigate through
the on-screen menus
GUIDE displays the
program guide
A, B, C access on-screen
program guide menus.
Consult the set-top box
manual for information
on these keys
VOL +/ increases or
decreases the volume
MUTE turns the volume off
and back on
PVR/VOD/VCR CONTROLS
replays the previous few
seconds of a program
LIST displays a list of programs
that have been recorded
LIVE TV displays live television
programming
INPUT allows the user to
select which input signal to use
PICTURE-IN-PICTURE (PIP)
ON-OFF turns on and off the
picture-in-picture feature
SWAP reverses the PIP window
and the active channel on
the main screen
HELP displays the on-screen
help system
POWER turns the currently
selected device on and off;
also activates Master Power
DEVICE KEYS allow you to
select which device to setup
and operate
PAGE +/ moves the on-screen
guide forward and backward
INFO displays channel and
program information
MENU displays the main
on-screen menu
CH +/ changes the channel
up and down
FAV steps through your
favorite channels
VOD allows quick access
to the Video on Demand system
LAST displays the last
LAST displays the last
channel viewed
NUMBER KEYS allow direct
access to specific channels
and menu options
ASPECT allows the user to
change the aspect ratio
on the set-top box
MOVE changes the location
of the PIP window on the
main screen
CH+/ changes the
channel in the PIP window
LIST
7
4
1
8
5
2
9
6
3
0
SWAP
MOVE
ON
OFF
CH
PIP
FAV
VOD
MUTE
OK
VOL
CH
LAST
T
V
A
U
X
V
C
R
C
B
L
D
V
D
LIVE
TV
EXIT
INFO
GUIDE
MENU
PPV
HELP
TV/VCRASPECT
INPUT
The diagram below provides a brief description of each key on your Adelphia remote control.
The function descriptions will allow you to become more familiar with your remote. Functions
may vary between different services. Please refer to your set-top box manual for descriptions of
specific functions.
The function descriptions will allow you to become more familiar with your remote. Functions
may vary between different services. Please refer to your set-top box manual for descriptions of
specific functions.
Test the code by trying various functions. If the primary function keys fail to respond
satisfactorily try the next code listed for the manufacturer.
satisfactorily try the next code listed for the manufacturer.
If you have tried all the codes listed for the manufacturer and the device does not
respond, try to program the device using SmartScan
respond, try to program the device using SmartScan
™
as described in section 5.
Remember to record your device codes in section 11 when you are done.
By default, your Adelphia remote controls volume through the TV. To allow volume control
through a different device:
through a different device:
To return volume control to the default state:
6
Manual Programming
To manually set up the Adelphia remote to operate a device, find the manufacturer of the
device in the list of manufacturers’ codes. The codes are logically grouped by device type in
section 12. Then perform the following steps:
device in the list of manufacturers’ codes. The codes are logically grouped by device type in
section 12. Then perform the following steps:
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash.
CBL key. The CBL key will continue to flash.
Press and release the VOLUME UP key, the CBL key will remain on.
Press and release the VOLUME DOWN key. The CBL key will turn off when VOLUME
DOWN is pressed, and will turn on when released.
DOWN is pressed, and will turn on when released.
Press and release the key corresponding to the device you wish to use to control
volume (CBL or AUX). After you release the key, the CBL key will flash three times and
turn off.
volume (CBL or AUX). After you release the key, the CBL key will flash three times and
turn off.
3
1
2
SmartScan
™
will allow you to easily try all the available programming codes for the selected
device and find the best match. If you prefer manual programming or already have the device
codes you may also program the remote manually using the steps in section 6.
codes you may also program the remote manually using the steps in section 6.
Turn on the power for the device to be programmed.
Begin the SmartScan
™
procedure by pressing and holding the associated device key
(AUX, VCR/DVD, TV) until all device keys on the remote begin to flash (approximately 3
seconds). Release the device key.
seconds). Release the device key.
If the device you’re attempting to program matches the selected device key (e.g. TV
component with the TV device key) proceed to step 5.
component with the TV device key) proceed to step 5.
If the device you’re attempting to program does not match the selected key (e.g. a
second VCR programmed to the AUX device), locate the correct prefix code for the
device you wish to program from the table listed below. Press and release the number
key that matches the prefix code.
second VCR programmed to the AUX device), locate the correct prefix code for the
device you wish to program from the table listed below. Press and release the number
key that matches the prefix code.
Press and release the POWER key. The device key will stop flashing and remain on.
Point the remote control at the selected device.
Press and hold the UP ARROW key until the device turns off. While holding the UP
ARROW key the remote will send a new code approximately once every second. The
device button will blink each time a new code is sent. If you pass the code that turns off
the device, press the DOWN ARROW key to return to the previous code.
ARROW key the remote will send a new code approximately once every second. The
device button will blink each time a new code is sent. If you pass the code that turns off
the device, press the DOWN ARROW key to return to the previous code.
When the device turns off, you have found a candidate code. Press the POWER key to
turn device back on. Test various functions using the remote control to determine if this
code will work. If primary functions do not work, make sure the device is still on then
resume SmartScan
turn device back on. Test various functions using the remote control to determine if this
code will work. If primary functions do not work, make sure the device is still on then
resume SmartScan
™
by pressing the UP ARROW key to find another device code.
Once you have found a satisfactory code, press OK to lock the code. The power of the
device must be on. The device key will then flash three times. Go to section 10 to recall
and record your device codes. When all the codes have been attempted the device
button will flash rapidly.
device must be on. The device key will then flash three times. Go to section 10 to recall
and record your device codes. When all the codes have been attempted the device
button will flash rapidly.
1
2
3
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash.
CBL key. The CBL key will continue to flash.
Press and release the VOLUME UP key. The CBL device key will stop flashing and stay
on. Press and release the VOLUME DOWN key, and then press and release the OK key.
After you release the OK key, the CBL device key will flash three times and turn off.
on. Press and release the VOLUME DOWN key, and then press and release the OK key.
After you release the OK key, the CBL device key will flash three times and turn off.
1
2
4
5
Press and hold the device key to be programmed until all device keys begin to flash
(approximately 3 seconds). Release the key. The selected device key will continue to flash.
(approximately 3 seconds). Release the key. The selected device key will continue to flash.
Enter the four digit code for the desired device using the number keys. After pressing the
first digit, the device key will light and remain on. After the last digit is pressed the device
key will flash three times and turn off. You will not see any flashes if the code has failed.
first digit, the device key will light and remain on. After the last digit is pressed the device
key will flash three times and turn off. You will not see any flashes if the code has failed.
1
2
6
Prefix
0
1
4
5
5
Device
TV
VCR/DVD
Audio Receivers
TV Combo Units
TV Combo Units
7
The Adelphia remote control is already programmed with the code for your Motorola
®
set-top
box. The following sections will help you program your remote to control your other
entertainment components.
entertainment components.
3
4
8
This four mode remote control has been
programmed to control your Motorola set-top
box and can be programmed to control up to
three additional entertainment components by
following these easy instructions.
programmed to control your Motorola set-top
box and can be programmed to control up to
three additional entertainment components by
following these easy instructions.
5
SmartScan™ Automatic Programming
9
The Master Power function allows you to turn off and on two or more devices simultaneously
with a single press of the power button. The following steps describe how to program the
Master Power Control function:
with a single press of the power button. The following steps describe how to program the
Master Power Control function:
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash.
CBL key. The CBL key will continue to flash.
Press and release the POWER key.
Individually press and release each device key corresponding to the components you
wish to be controlled by Master Power (starting with the cable device key). NOTE: If no
keys are pressed in this step, no change will occur in Master Power programming.
wish to be controlled by Master Power (starting with the cable device key). NOTE: If no
keys are pressed in this step, no change will occur in Master Power programming.
1
2
3
Press and release the POWER key. The CBL key will flash three times and turn off.
Manually turn on all devices. Then test the Master Power control by pressing the
POWER key.
POWER key.
4
5
To disable Master Power, repeat the previous steps selecting only one device for Master Power (any
device can be selected). The remote will now control the power ON/OFF of each device separately.
device can be selected). The remote will now control the power ON/OFF of each device separately.
NOTE: Once Master Power has been programmed for two or more devices, pressing the POWER
key in normal operation will cause the remote to transmit the POWER on/off commands for
those devices selected during Master Power programming,
key in normal operation will cause the remote to transmit the POWER on/off commands for
those devices selected during Master Power programming,
To override this and transmit a POWER on/off command for a device not included in the Master
Power selection, press the DEVICE key for that device and immediately press the POWER key.
Power selection, press the DEVICE key for that device and immediately press the POWER key.
Before You Begin
2
3
Install Batteries
Congratulations!
1
7
Programming Volume Control
8
Master Power Control