Справочник Пользователя для Pelco C1043M-A
Pelco Manual C1043M-A (2/96)
5
3.3 ICI3008/ICI3016 INSTALLATION
Refer to Figure 1 for a typical ICI3000P configuration.
1.
Connect the 9-pin switcher interface cable (supplied
with the ICI3008/ICI3016 switcher) into the port
labeled “RS 232” of the ICI3000P.
with the ICI3008/ICI3016 switcher) into the port
labeled “RS 232” of the ICI3000P.
2.
Connect the modular phone plug of the switcher
interface cable into the port labeled “DATA IN” on
the ICI3008/ICI3016 switcher.
interface cable into the port labeled “DATA IN” on
the ICI3008/ICI3016 switcher.
3.
Connect the video output from your cameras to the
BNC’s labeled “VIDEO INPUTS” on the ICI3008/
ICI3016.
BNC’s labeled “VIDEO INPUTS” on the ICI3008/
ICI3016.
4.
Connect a coaxial cable between the port labeled
“VIDEO OUT” of the ICI3008/ICI3016 and the port
labeled “VIDEO IN” of the ICI3000P.
“VIDEO OUT” of the ICI3008/ICI3016 and the port
labeled “VIDEO IN” of the ICI3000P.
5.
If multiple ICI3008/ICI3016 switchers are being cas-
caded, connect a coaxial cable from the last video
input of the first Inter-Check switcher to the port
labeled “VIDEO OUT” of the second Inter-Check
switcher. Remove the cover of the second Inter-
Check switcher and set the 8 position dip switch to
0001 0000. Remove the cover of the first Inter-
Check switcher and set the 8-position dip switch to
caded, connect a coaxial cable from the last video
input of the first Inter-Check switcher to the port
labeled “VIDEO OUT” of the second Inter-Check
switcher. Remove the cover of the second Inter-
Check switcher and set the 8 position dip switch to
0001 0000. Remove the cover of the first Inter-
Check switcher and set the 8-position dip switch to
0000 1000 where 0 = ON and 1 = OFF (refer to
Figure 8).
Figure 8).
6.
Connect the desired alarm outputs to any peripheral
equipment requiring a normally open contact. (Refer
to Figure 5 for pin assignment information.)
equipment requiring a normally open contact. (Refer
to Figure 5 for pin assignment information.)
7.
Connect an “IBM AT” compatible keyboard into the
ICI3000P input labeled “KEYBOARD”.
ICI3000P input labeled “KEYBOARD”.
8.
Power up the Inter-Check units using the transformers
supplied with each unit.
supplied with each unit.
9.
To verify communication between the Inter-Check
switcher and the ICI3000P, press [F9]. Press [F9]
again. Next, select camera one by entering a [1] one
followed by the [ENTER] key. The first red light
labeled “1” on the first switcher should be on. Repeat
this step for each camera input on each switcher. If
an 8 or 16-position switcher has a second switcher
cascaded from it, selecting camera 8 or 16
respectively will cause the first light of the second
switcher to be activated.
switcher and the ICI3000P, press [F9]. Press [F9]
again. Next, select camera one by entering a [1] one
followed by the [ENTER] key. The first red light
labeled “1” on the first switcher should be on. Repeat
this step for each camera input on each switcher. If
an 8 or 16-position switcher has a second switcher
cascaded from it, selecting camera 8 or 16
respectively will cause the first light of the second
switcher to be activated.
P E L C O
SYSTE M BE I NG I NI TI ALI ZED!
P R E S S
1
K E Y
O N
K E Y B O A R D
F O R
A P P R O X I MA T E L Y
3
S E C O N D S
SYSTEM BEING INITIALIZED
Press the [1] key on the keyboard for
approximately 3 seconds.
P E L C O
I CI 3000P BY PE LCO
VE R. 4 . 0
ROM CHE CK = XXXX
CALC.
VE R. 4 . 0
ROM CHE CK = XXXX
CALC.
ROM CHE CK=YYYY
SYSTE M BE I NG I NI TI ALI ZED!
MM VE R.
MM VE R.
Z. Z
T E X T
O N
S C R E E N
WI L L
F L A S H
I F
D E F A U L T S
WE R E
L O A D E D
ICI3000P by PELCO
Ver. 4.0
ROM Check = xxxx
Calc. ROM Check = yyyy
System Being Initialized
MM Ver. z.z
Ver. 4.0
ROM Check = xxxx
Calc. ROM Check = yyyy
System Being Initialized
MM Ver. z.z
Text on screen will flash
if defaults were loaded.
Figure 3. Defaulting Inter-Check System
!!!Defaults Loaded!!!