Справочник Пользователя для Pelco MPT9500TD
Pelco Manual C535M-B (8/98)
13
and on the monitor the following screen will appear:
NOTE:
Before programming a tour
for the
FIRST TIME
, it is recom-
mended that you clear the pro-
gramming area by pressing the
turbo button on the joystick (see
Figure 7).
gramming area by pressing the
turbo button on the joystick (see
Figure 7).
F1 TO EXIT
JOYSTICK
ENTER VALUE
F2 NEXT
STEP
1 2 3 4 5
DWL
PRE
JOYSTICK
ENTER VALUE
F2 NEXT
STEP
1 2 3 4 5
DWL
PRE
Flashing Cursor
→
→
→
→
Dwell Time
(in seconds)
(in seconds)
Preset
Address
Address
SET PRESET?
JOYSTICK
F1 TO EXIT
YES
NO
JOYSTICK
F1 TO EXIT
YES
NO
❊
→
→
Joystick operation for Standard Coaxitron
®
mode is the same as that already de-
scribed for Extended and RS-485 mode. If the PRESET SET key has been hit acci-
dentally and you wish to exit, use the joystick to position the * character in the “NO”
row and press the F1 key. If setting a preset was really intended then make sure the
* character is positioned in the “YES” row and press the F1 key. The preset is com-
plete. Continue to the next preset position and repeat this section to add more pre-
sets.
dentally and you wish to exit, use the joystick to position the * character in the “NO”
row and press the F1 key. If setting a preset was really intended then make sure the
* character is positioned in the “YES” row and press the F1 key. The preset is com-
plete. Continue to the next preset position and repeat this section to add more pre-
sets.
4.3.2.2 Preset Scans
The standard Coaxitron
®
Preset receiver will sequence through all of its available
presets at a predefined dwell. To evoke this option, key in the number from 5 up to
64 seconds. Next, press the PAN/AUTO key. The receiver will cycle through its pre-
sets in ascending order up to 360 cycles, then it will stop and need to be initiated
again for further sequencing.
64 seconds. Next, press the PAN/AUTO key. The receiver will cycle through its pre-
sets in ascending order up to 360 cycles, then it will stop and need to be initiated
again for further sequencing.
4.3.3 Preset Tours (Standard or Extended Coaxitron
®
Modes)
MPT9500TD Only
To program a tour for a Coaxitron
®
receiver, press the number 4 key followed by the
F2 key. On the monitor, the following screen will appear:
Some preliminary remarks regarding preset tours and the terms used in the above
screen might be in order. Preset tours consist of the sequential execution of a pro-
grammed series of up to 65 previously set presets, viewed one at a time, at the end
of which the cycle repeats until interrupted. You will recall that there are 32 possible
preset addresses. When programming a “tour” any (up to 32) of the possible preset
address positions may be included in the tour since 65 preset positions (called
“steps”) are available in a tour. Only 5 programmable steps at a time appear on any
given screen and each screen of 5 steps is called a page, giving a total of 13
“pages”. Assuming you had programmed the first 5 steps, hitting the F2 key would
bring up page 2 (steps 6-10) which would appear as follows:
screen might be in order. Preset tours consist of the sequential execution of a pro-
grammed series of up to 65 previously set presets, viewed one at a time, at the end
of which the cycle repeats until interrupted. You will recall that there are 32 possible
preset addresses. When programming a “tour” any (up to 32) of the possible preset
address positions may be included in the tour since 65 preset positions (called
“steps”) are available in a tour. Only 5 programmable steps at a time appear on any
given screen and each screen of 5 steps is called a page, giving a total of 13
“pages”. Assuming you had programmed the first 5 steps, hitting the F2 key would
bring up page 2 (steps 6-10) which would appear as follows:
F1 TO EXIT
JOYSTICK
ENTER VALUE
F2 NEXT F3 PREV
STEP
6 7 8 9 10
DWL
PRE
JOYSTICK
ENTER VALUE
F2 NEXT F3 PREV
STEP
6 7 8 9 10
DWL
PRE
→
→
→
→
Flashing Cursor
Dwell Time
(in seconds)
(in seconds)
Preset
Address
Address