Справочник Пользователя для Hitachi 25K 60SX12B
USING THE REMOTE TO CONTROL AUDIO EQUIPMENT FUNCTIONS
37
USING THE REMOTE TO CONTROL AUDIO EQUIPMENT FUNCTIONS
Operating the pre-coded function for your audio equipment.
This remote is designed to operate different types of audio equipment. You must first
program the remote to match the remote system of your audio equipment.
program the remote to match the remote system of your audio equipment.
Remote Control Illustration
1. Set the MULTI-PAGE select switch to "AUDIO".
2. Turn ON the audio component you wish to control with your remote control (AMP, CD
or TAPE).
3. Aim the remote control at the front of your audio equipment.
4. While holding down the button on the remote which corresponds with the component
you wish to control (AMP, CD, or TAPE), enter the 2 digit preset code that matches your
audio component as shown on page 30. The remote will turn off your audio component
when the correct 2 digit preset code is entered. When this occurs, the remote control is
programmed for your audio component. If the audio component does not turn off after 5
seconds, try a different 2 digit preset code.
5. The remote will now control your audio component.
6. Repeat steps 2-5 until all audio equipment preset codes are programmed into the
remote.
1. Set the MULTI-PAGE select switch to "AUDIO".
2. Turn ON the audio component you wish to control with your remote control (AMP, CD
or TAPE).
3. Aim the remote control at the front of your audio equipment.
4. While holding down the button on the remote which corresponds with the component
you wish to control (AMP, CD, or TAPE), enter the 2 digit preset code that matches your
audio component as shown on page 30. The remote will turn off your audio component
when the correct 2 digit preset code is entered. When this occurs, the remote control is
programmed for your audio component. If the audio component does not turn off after 5
seconds, try a different 2 digit preset code.
5. The remote will now control your audio component.
6. Repeat steps 2-5 until all audio equipment preset codes are programmed into the
remote.
NOTES:
1. If your audio component cannot be operated after performing the above procedures, this
means that your audio component code has not been precoded into the remote.
2. In the unlikely event that your audio component cannot be operated after performing the
above procedures, please consult your audio component operating guide.
3. The remote control will remember the codes you have programmed in until the batteries
are removed from the remote control. After replacing the batteries repeat the entire
programming procedure stated above.
4. If your audio component does not have a power function, the remote will issue another
obvious function that the audio component will respond to, such as CD open/close.
5. The default for AUDIO Mode is AMP.
6. If you wish to control your Receiver or misc audio equipment, you must follow the remote
programming procedure shown above. You may use the AMP, CD, or TAPE buttons, but
note that these buttons may not be used for more than one component.
1. If your audio component cannot be operated after performing the above procedures, this
means that your audio component code has not been precoded into the remote.
2. In the unlikely event that your audio component cannot be operated after performing the
above procedures, please consult your audio component operating guide.
3. The remote control will remember the codes you have programmed in until the batteries
are removed from the remote control. After replacing the batteries repeat the entire
programming procedure stated above.
4. If your audio component does not have a power function, the remote will issue another
obvious function that the audio component will respond to, such as CD open/close.
5. The default for AUDIO Mode is AMP.
6. If you wish to control your Receiver or misc audio equipment, you must follow the remote
programming procedure shown above. You may use the AMP, CD, or TAPE buttons, but
note that these buttons may not be used for more than one component.
1 PRECODED AMP, CD, OR TAPE buttons
These buttons transmit the chosen precoded audio component codes.
2 EXCLUSIVE TV buttons
These buttons are for operating the TV.
These buttons transmit the chosen precoded audio component codes.
2 EXCLUSIVE TV buttons
These buttons are for operating the TV.