Справочник Пользователя для Iomega eximac

Installation Guide

This guide shows how to install the portable SCSI Jaz drive on a
Macintosh. If you encounter any problems while installing your Jaz
drive, refer to the "Troubleshooting" section in the Jaz User's Guide.

Unpack the Jaz drive and accessories.

Data Cable

Jaz Drive

50HD to 25D
Cable Converter

Jaz "tools" Disk (contains Jaz Tools software)

Manuals and
Install Diskettes*

External Power
Supply

1GB

tools

You will not need an install diskette to install Jaz Tools on your Macintosh.

Shut down your Mac, turn off all connected
devices, and pick up the Jaz data cable.

WARNING

Always turn off power to the computer and all devices

connected to it (such as printers or drives) before beginning any
computer hardware change.

Installation Guide

for Macintosh

Connect one end of the data cable to either
SCSI port on the back of your drive, and PUSH
until connector locks into place.

(If the connector

does not go on easily, try turning it over.)

Jaz Connector

I A O

SCSI ID

Term

PWR

DO NOT attempt to stand the Jaz drive

CAUTION

on its side! NEVER move the drive when in use!

M To Remove the Jaz Data Cable: Squeeze the spring locks
on both sides of the data cable connector while pulling on
the connector.

Use the 50HD to 25D cable converter to
connect the other end of the data cable to the
built-in SCSI connection on your Macintosh.

I A O

SCSI ID

Term

PWR

PowerBook Users You need a special PowerBook cable to

connect the Jaz drive. Check with your Iomega dealer or call Iomega
at 1-800-MY-STUFF to order a Jaz PowerBook cable.

driv

1
GB

SCSI

(Open up for Step 5)

United States FCC Information

The computer equipment described in this installation guide generates and uses radio frequency (RF) energy. If the

equipment is not installed and operated in strict accordance with the manufacturer’s instructions, interference to

radio and television reception may result.

M Interference

This equipment complies with Part 15 of the FCC Rules and its operation is subject to the following

conditions: (1) the equipment may not cause harmful interference, and (2) the equipment must accept any

interference received, including interference that may cause undesired operation.

Part 15, Class B, of the FCC Rules, is designed to provide reasonable protection against radio and television

interference in a residential installation. Although the equipment has been tested and found to comply with allowed

RF emission limits, as specified in the above cited Rules, there is no guarantee that interference will not occur in a

particular situation. Interference can be determined by turning the equipment off and on while monitoring radio or

television reception. The user may be able to eliminate any interference by implementing one or more of the

following measures:

•

Reorient the affected device and/or its receiving antenna.

•

Increase the distance between the affected device and the computer equipment.

•

Plug the computer and its peripherals into a different branch circuit from that used by the affected device.

WARNING

Only the manufacturer’s cable or an equivalent double shielded, host interface cable should be used

with external subsystems. Other types of cables may violate FCC rules and regulations. Also, changes or

modifications to the electronics or enclosure of this product must be expressly approved by Iomega; otherwise, the

user’s authority to operate the equipment may be voided by the FCC.

Canadian DOC Information

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital devices as set out in

the Radio Interference Regulations of the Canadian Department of Communications.

Iomega's Automated Help Systems

Internet Home Page:............................................................

http://www.iomega.com

America Online™................................................................

Keyword:

Iomega

Microsoft Network...............................................................

GoWord:

Iomega

Automated FAX Help (U.S. & Canada only).....................

1-801-778-5763

Automated E-Mail................................................................

support@iomega.com

(Please type "Jaz" in the subject header when sending your E-Mail)

Iomega Bulletin Board.........................................................

1-801-778-5888

8,N,1; 9600 baud and above; ANSI (24 hrs - Download only)

Repair and Return Information...........................................

1-801-779-6100

(No technical support information is available at this number.)

One-on-One Iomega Technical Support

One-on-One Technical Support is free of charge for issues Iomega determines

relate to a defect in an Iomega product. Other issues are charged at the rate of

$19.99 per incident for Jaz products. You can call 1-888-4-IOMEGA, toll-free,

to charge the support cost to your credit card (VISA, MasterCard, American

Express, or Discover), or you can call 1-900-988-4747 to put the support cost

on your phone bill. Either way, the charge will be reversed if your issue is

found by Iomega to be due to a product defect.

Iomega's technical support associates are ready to take your call Monday

through Friday from 6 a.m. to 6 p.m. Mountain time (U.S. & Canada only).

European Support Numbers

Refer to the electronic manual included with your Jaz software package for a

complete list of European support numbers.

EN137104

Printed on recycled paper

swirl, hand and eye are trademarks of, Iomega Corporation. All other product and brand names are the

property of their respective companies.