Справочник Пользователя для cat-eye double shot
○
○
○○○○○○
A
B
C
○○○○○○
○○○○
○○○○○○○○
○○○○○○○○
1
2
4
7 or 8
2
LOCK
1
9
2,3
7 or 8
0
2, 3
1.
B-2
B-3
2.
B-1
1.
or
*H32
2.
0
3.
1
#533-8825
#534-1830
#534-1706
#534-1707
UL
#534-1708
UK
#534-1709
EC
#534-1710
AS
#534-1711
#533-8880
#534-1832
#534-1831
B-1
B-2
B-3
Approx.
3
hours
Standard charging time
Charging indicator state
Orange Light
: Connected to power source
Blinking Red Light
: Charging
Green Light
: Charging is completed
Approx.
5
hours
Run time
HOW TO MOUNT TO A BICYCLE
Installing the bracket/light unit
Attach bracket H31 or H32 to the handlebar.
NOTE: Select H31 for oversized handlebars.
1. Mount a rubber pad and the bracket onto the handlebar. 2 thicknesses of
NOTE: Select H31 for oversized handlebars.
1. Mount a rubber pad and the bracket onto the handlebar. 2 thicknesses of
rubber pads are supplied; if necessary, cut the rubber pad to fit.
2. Tighten and then close the lever to secure it. Make sure the bracket does not
rotate on the handlebar.
CAUTION!: Be sure to adjust the angle of the light’s beam by referring to the
“How to Adjust Beam Angle” section in this manual before operat-
ing the lighting system.
ing the lighting system.
3. Mount the light unit onto the bracket.
To remove unit after use, pull it out while pressing the button on the bracket.
CAUTION!: Make sure the light unit is cool to the touch before removing it.
Installing Battery Unit
Mount the battery unit on the bicycle frame.
Before using the light, make sure the battery is correctly stored in its neoprene
bag.
Before using the light, make sure the battery is correctly stored in its neoprene
bag.
CAUTION!: When mounting the unit, make sure that the seam of the battery bag is
facing down and the fold line is in front. Wind the fixing strap around
the center of the battery unit.
the center of the battery unit.
1. Wrap the fixing strap around the top tube to secure the unit.
CAUTION!: Wrap the strap over the top tube but under the gear and brake cables.
Wrapping the strap over the cables is dangerous as it may interfere
with braking and gear shifting.
with braking and gear shifting.
2. Use the support strap to secure the battery unit to the down tube to prevent
it from rolling.
NOTE: The battery can also be mounted on alternate positions on the bicycle.
However, please make sure that the seam of the battery bag is facing
down, and the fold line is in front. This will help prevent any water from
entering the bag.
down, and the fold line is in front. This will help prevent any water from
entering the bag.
Connecting and Securing Cables
Align the male and female cable ends and connect them. Turn the plugs so that
they are securely locked. Fix the cables to your frame and/or stem to keep them
secured.
they are securely locked. Fix the cables to your frame and/or stem to keep them
secured.
CAUTION!: Pay attention to the arrangement of the cable so that it does not inter-
fere with the handling of the bicycle. Do not secure the cable at an
acute angle because the wire inside the cable may break.
acute angle because the wire inside the cable may break.
Quick lever
Down Tube
Fixing Strap
Fixing Strap
Top Tube
Gear & Brake Cables
Line
Rubber pad
Handlebar
Button
HOW TO USE
A
Switching on/off
To switch the light on/off, press the button directly behind the light unit.
B
How to Adjust Beam Angle
If the light unit is mounted on the bicycle, adjust the beam angle so as not to blind oncoming traffic.
C
How to Charge Battery Unit
Important!
• Be sure to use only the supplied battery charger. This charger can accept 100-240 volts.
• Do not completely remove the battery unit from the battery bag.
• After charging, return the battery to its original storage state. Do not allow water to enter the battery bag.
• The standard charging time and run time are guideline values and depend on the operating environment.
• If the battery unit repeatedly does not meet the proper run time even though it is fully charged, it
• Do not completely remove the battery unit from the battery bag.
• After charging, return the battery to its original storage state. Do not allow water to enter the battery bag.
• The standard charging time and run time are guideline values and depend on the operating environment.
• If the battery unit repeatedly does not meet the proper run time even though it is fully charged, it
might be at the end of its operating life. Replace the old battery unit with a new one. The used
battery unit should be disposed of properly according to local regulations.
battery unit should be disposed of properly according to local regulations.
1. Remove the support strap from the battery bag and open the bag.
2. Connect the jack to the battery charger.
3. Plug the battery charger to an AC outlet.
2. Connect the jack to the battery charger.
3. Plug the battery charger to an AC outlet.
NOTE: When charging is complete, the indicator light changes from flashing red to green.
4. When charging is complete, unplug the charging adapter. Refer to the diagrams on the left to rearrange
the cable and use the seal strap to tightly close the opening.
CAUTION!: When securing the battery to the frame, make sure the fixing strap attaches to the center of the
battery unit.
How to Store Battery Unit
The battery unit is stored in its bag as shown in the figure. In case the battery unit is out of its bag, be
sure to return it to its original state. Failure to follow these instructions may result in rainwater entering
the battery bag, leading to problems with the unit.
the battery bag, leading to problems with the unit.
Button
Charging Indicator
To AC Power Outlet
Charging jack
Cable Arrangement
Seal Strap
Fixing Strap
Quick lever
Loosen
the lever
the lever
Seam
Plug
Charging jack
SPECIFICATIONS
Light Source ------------- Two High-Power White LEDs
Battery Unit -------------- Nickel hydride battery
Battery Unit -------------- Nickel hydride battery
(Ni-MH/12V 2700mAh)
Battery Charger --------- CHR-2700(AC100V-240V
50/60Hz 0.5A)
Operating Time ---------- Approx. 5 hours
Standard charging time Approx. 3 hours
Temperature range ----- Charging: -10
Standard charging time Approx. 3 hours
Temperature range ----- Charging: -10
°C - 40°C
Operating: -15
°C - 45°C
Recharge/discharge number of times
---------------------------- About 300 times
(until the rated capacity
drops to 50%)
drops to 50%)
Seam
Fold Line
* The specifications and design are subject to change without notice.
SPARE PARTS
Light Unit
Battery Charger
Bracket H32
Bracket H31
Helmet mount
Battery Unit/
Battery Bag
Battery Bag Set
Extension cable