Справочник Пользователя для Chamberlain 3585s 3-4 hp
27
Using the Wall-Mounted Door Control
THE SMART CONTROL PANEL
TM
Press the push bar to open or close the door. Press again
to reverse the door during the closing cycle or to stop the
door while it's
opening.
to reverse the door during the closing cycle or to stop the
door while it's
opening.
This door control
contains a motion
sensing detector that
will automatically turn
on the light when it
detects a person
entering the garage.
contains a motion
sensing detector that
will automatically turn
on the light when it
detects a person
entering the garage.
Light feature
Press the
Light button
to turn the opener light on or off. It will not control
the opener lights when the door is in motion. If
Light button
to turn the opener light on or off. It will not control
the opener lights when the door is in motion. If
you turn it on and then activate the opener, the light will
remain on for 4-1/2 minutes. Press again to turn it off
sooner. The 4-1/2 minute interval can be changed to 1-1/2,
2-1/2, or 3-1/2 minutes as follows: Press and hold the Lock
button until the light blinks (about 10 seconds). A single
blink indicates that the timer is reset to 1-1/2 minutes.
Repeat the procedure and the light will blink twice,
resetting the timer to 2-1/2 minutes. Repeat again for a
3-1/2 minute interval, etc., up to a maximum of four blinks
and 4-1/2 minutes.
remain on for 4-1/2 minutes. Press again to turn it off
sooner. The 4-1/2 minute interval can be changed to 1-1/2,
2-1/2, or 3-1/2 minutes as follows: Press and hold the Lock
button until the light blinks (about 10 seconds). A single
blink indicates that the timer is reset to 1-1/2 minutes.
Repeat the procedure and the light will blink twice,
resetting the timer to 2-1/2 minutes. Repeat again for a
3-1/2 minute interval, etc., up to a maximum of four blinks
and 4-1/2 minutes.
When using the opener lights as working lights, we
recommend that you first disable the motion sensor. See
Automatic Light Feature, below.
recommend that you first disable the motion sensor. See
Automatic Light Feature, below.
Motion Sensing (Automatic Light Feature): The
opener light will turn on automatically when a
person enters the garage. When a person walks
in front of the door control, the light will come on
opener light will turn on automatically when a
person enters the garage. When a person walks
in front of the door control, the light will come on
for five minutes, then shut off. This feature works by
detecting body heat.
detecting body heat.
To disable this feature, push the motion sensing button on
the side of the door control.
the side of the door control.
We recommend that you disable the motion sensor when
using the opener lights as working lights. Otherwise, they
will turn off automatically if you are working beyond the
sensors range.
using the opener lights as working lights. Otherwise, they
will turn off automatically if you are working beyond the
sensors range.
Lock feature
Designed to prevent operation of the door from
hand-held remote controls. However, the door will
open and close from the Door Control, the
hand-held remote controls. However, the door will
open and close from the Door Control, the
Outdoor Key Switch and the Keyless Entry Accessories.
To activate, press and hold the Lock button for 2 seconds.
To turn off, press and hold the Lock button again for
2 seconds. The Lock feature will also turn off whenever the
“learn” button on the motor unit panel is activated.
2 seconds. The Lock feature will also turn off whenever the
“learn” button on the motor unit panel is activated.
Motion Sensing
On/Off
Prog <Learn>
Hour
Minute
Language
Degrees (F/C)
Lock Button
Light
Button
Button
Push
Bar
Bar
LOCK
LIGHT
(PROG) Learn Feature
The door control is equipped with a PROG <LEARN>
button to assist in learning remote controls to the unit.
Press the PROG <LEARN> button once to initiate LEARN
mode and the display will show ‘Learn Remote Control -
Press Learn Button Again to Confirm’. Press the PROG
<LEARN> button a second time and the display will show
‘Learn Mode - Press Remote Control Button to Learn
Remote.’ Press the button of the remote control to be
learned and the worklight will blink to confirm the remote
control has been learned.
button to assist in learning remote controls to the unit.
Press the PROG <LEARN> button once to initiate LEARN
mode and the display will show ‘Learn Remote Control -
Press Learn Button Again to Confirm’. Press the PROG
<LEARN> button a second time and the display will show
‘Learn Mode - Press Remote Control Button to Learn
Remote.’ Press the button of the remote control to be
learned and the worklight will blink to confirm the remote
control has been learned.
Hour & Minute Feature
Press or hold either of these side buttons to
increment the hour or minute displayed on
the LCD display.
Press or hold either of these side buttons to
increment the hour or minute displayed on
the LCD display.
(LANG) Language Feature
Press this side button to toggle between the three
languages - English, French and Spanish.
languages - English, French and Spanish.
Degrees F/C Feature
Press this side button to toggle the temperature
units between Fahrenheit and Celsius.
units between Fahrenheit and Celsius.
Display Contrast Adjustment
Press and hold the light button then push the hour button
to increase the contrast or the minute button to decrease
the contrast.
to increase the contrast or the minute button to decrease
the contrast.
LIGHT
LOCK
H
M