Справочник Пользователя для Kompernass parkside phlg 2000-kh 3152 hot air gun
6 GB
Hot air gun PHLG 2000 SE
For removing, reshaping, preheating,
defrosting etc.
defrosting etc.
Introduction
For your safety
Please make sure you familiarise yourself fully with
the way the device works before you use it for the
fi rst time and that you understand how to handle
electrical power tools correctly. Further details can
be found in the operating instructions
the way the device works before you use it for the
fi rst time and that you understand how to handle
electrical power tools correctly. Further details can
be found in the operating instructions
.
In addition to the above, you must also strictly
observe the general safety advice
observe the general safety advice
contained
in the accompanying booklet. Use the device only
as described and for the indicated purposes. By
doing this you will be able to work with a high level
of safety and produce better results. Keep these
instructions in a safe place. If you pass the hot air
gun on to anyone else, please ensure that you also
pass on all the documentation.
as described and for the indicated purposes. By
doing this you will be able to work with a high level
of safety and produce better results. Keep these
instructions in a safe place. If you pass the hot air
gun on to anyone else, please ensure that you also
pass on all the documentation.
Proper use
The hot air gun is intended for the removal of paint,
for warming (e.g. heat-shrinkable sleeves) and
for reshaping and welding of plastics. It may also
be used for detaching glued connections and for
defrosting or thawing water pipes. It is not suitable
for defrosting pipes made from PVC or similar
materials. The device is also suitable for soldering
and tinning.
Any other use or modifi cation to the device shall
be considered as improper use and could give
rise to considerable dangers. The manufacturer
will not accept liability for loss or damage arising
from improper use. The device is not intended for
commercial use.
for warming (e.g. heat-shrinkable sleeves) and
for reshaping and welding of plastics. It may also
be used for detaching glued connections and for
defrosting or thawing water pipes. It is not suitable
for defrosting pipes made from PVC or similar
materials. The device is also suitable for soldering
and tinning.
Any other use or modifi cation to the device shall
be considered as improper use and could give
rise to considerable dangers. The manufacturer
will not accept liability for loss or damage arising
from improper use. The device is not intended for
commercial use.
Features and equipment
햲
Air
inlet
햳
ON/OFF switch (ON = setting 1 (375° C)
or setting 2 (550° C))
햴
Nozzle
햵
Heat
shield
햶
Refl
ector
nozzle
햷
Protector
nozzle
햸
Flat
nozzle
햹
Reducer
nozzle
Included items/
supplied accessories
supplied accessories
Check that all the items and accessories are
present immediately after unpacking:
present immediately after unpacking:
1 Hot air gun PHLG 2000 SE
1 Refl
1 Refl
ector
nozzle
1 Protector
nozzle
1 Flat
nozzle
1 Reducer
nozzle
1 General safety advice for electrical tools
1 Operating
1 Operating
instructions
1 Guarantee
documentation
Technical information
Nominal voltage:
230 V ~ 50 Hz
Power consumption:
Setting 1: 1000 W
Setting
2:
2000
W
Air fl ow approx.:
Setting 1: 300 l/min,
Setting 2: 500 l/min
Temperature
Nozzle outlet approx.:
Nozzle outlet approx.:
Setting 1: 375° C,
Setting 2: 550° C
Protection class:
II /
쓑
The sound pressure level (A) of the device is typi-
cally less than 70 dB(A).
cally less than 70 dB(A).
Introduction