Справочник Пользователя для Bay Technical Associates BayTech DS72
DS72 Host Module
23
Network Port Configuration
This allows access to the menu to change such options as the IP Address, Subnet Mask, Gateway,
DHCP, and Telnet; all of which are necessary during initial startup. The Connection Inactivity
Timeout allows you to enable/disable whether the firmware ends your session or “times out.”
Disabling the Carriage Return Translation allows you to bypass all unnecessary carriage returns, and it
will send you straight to the next “end of line.”
DHCP, and Telnet; all of which are necessary during initial startup. The Connection Inactivity
Timeout allows you to enable/disable whether the firmware ends your session or “times out.”
Disabling the Carriage Return Translation allows you to bypass all unnecessary carriage returns, and it
will send you straight to the next “end of line.”
IMPORTANT: For network access, you must configure the IP addresses, Subnet Mask, and
Gateway Address. The module must be reset for network changes to take effect.
Gateway Address. The module must be reset for network changes to take effect.
IP Address
The IP address is the network address assigned by your network manager for your network. The IP
Address consists of four bytes, each byte ranging from 0 to 255. This parameter must be programmed
before the Host Module may be accessed via the network.
Address consists of four bytes, each byte ranging from 0 to 255. This parameter must be programmed
before the Host Module may be accessed via the network.
Enter the Module IP Address (Example: 200.4.3.50), followed by <cr>. The Host Module resumes the
configuration menu. Default Module IP Address is 0.0.0.0. If you fail to enter the Module IP
Address in dotted decimal form, the Host Module responds again:
configuration menu. Default Module IP Address is 0.0.0.0. If you fail to enter the Module IP
Address in dotted decimal form, the Host Module responds again:
The Host Module responds indefinitely with the same request until the Module IP Address in entered
in the correct form.
in the correct form.
SNMP is ENABLED. Enable? (Y/N):
Network Configuration
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Gateway: 0.0.0.0
Ethernet Address: 00.C0.48.06.57.4C
Connection Inactivity Timeout (mins): Disabled
Carriage Return Translation: Disabled
Break Length (msecs): 350
DHCP is Disabled Bootp is Enabled Telnet is Enabled
IP Address........................1 Ethernet port IP Address 0.0.0.0
Subnet Mask.......................2 Tells when to listen
Gateway Address...................3 Router/Hub/Switch IP Address 0.0.0.0
Inactivity Timeout................4 Set timeout, in minutes (<=120,0=disable)
Carriage Return Translation.......5 Enable/Disable
Break Length......................6 Set in milliseconds (<=10000, 0=disable)
Bootp.............................7 Enable/Disable
DHCP..............................8 Enable/Disable
Telnet............................9 Enable/Disable
Exit...........................X,CR
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Gateway: 0.0.0.0
Ethernet Address: 00.C0.48.06.57.4C
Connection Inactivity Timeout (mins): Disabled
Carriage Return Translation: Disabled
Break Length (msecs): 350
DHCP is Disabled Bootp is Enabled Telnet is Enabled
IP Address........................1 Ethernet port IP Address 0.0.0.0
Subnet Mask.......................2 Tells when to listen
Gateway Address...................3 Router/Hub/Switch IP Address 0.0.0.0
Inactivity Timeout................4 Set timeout, in minutes (<=120,0=disable)
Carriage Return Translation.......5 Enable/Disable
Break Length......................6 Set in milliseconds (<=10000, 0=disable)
Bootp.............................7 Enable/Disable
DHCP..............................8 Enable/Disable
Telnet............................9 Enable/Disable
Exit...........................X,CR
Enter IP address in dotted decimal form :
Enter IP address in dotted decimal form :