Справочник Пользователя для Kompernass kh 3217 safety magnet lock set

q

4 installation templates

w

4 locks with magnet connectors

e

1 magnet key

r

4 lock plates

t

4 unlocking bars

y

4 extension inserts

u

1 drilling depth limiter

i

24 screws (12 mm)

o

4 T-inserts

a

4 marking stickers

Phillips head screwdriver
Drill
7 mm drill bit
Sharp object for making marks 
(such as a nail)

The safety magnet lock is intended for
locking drawers and doors of small
furniture (min. door thickness 12,7 mm).
It is not for securing house doors or
other heavy doors. It is not intended
for use in commercial or industrial
areas

 Do not store the magnetic parts of

the magnet lock near credit cards,
video cassettes or audio cassettes.
This leads to irreparable damaging
of the magnetic strips and tape!

 This magnet lock cannot guarantee

100% safety. Never leave your
children unsupervised for long!
Observe whether your children are
capable of opening the magnet
lock.

Note: Do not drill through the letters
in the installation template 

q

, always

drill through the marking (X). Please
note that when installing the safety
magnet lock in drawers, a free space
of 4 x 6 cm is required.

For surface-mounted doors / drawers
1a. Remove the narrow sticker 

from the installation template 

q

and stick it onto an appropriate
place on the cabinet inside wall
(see Fig. 1). When installing the
lock in drawers, place the installati-
on template 

q 

on the upper insi-

de drawer wall at the height of the
grip or knob. 

1b. Fold the installation template 

q

around the corner at the fold line

 

and mark the two screw holes 

(X) for the lock plate 

r

with a

sharp object (such as a nail). Pull
off the back of the sticker 

.

2. Press the door or drawer hard

against the sticker 

. When the

door / drawer is opened, the instal-
lation template 

q

will have been

transferred to the correct location
for further installation.

3. Smooth out the installation tem-

plate 

q

and mark four of the six

screw holes 

(X) (two above and

two below) for the lock 

w

(see Fig. 2).
Continue with Step 4.

For inset doors / drawers
1a. Measure the door thickness

(depth) / thickness of the drawer
front.
Draw the new markings for the 
screw holes of the lock plate 

r

onto the installation template 

q

:

To do this, move the markings
along the dotted arrow line by the
measured door thickness, starting
from the screw holes 

(X)  Make

certain that the new markings are
situated parallel to the screw holes

(X). Remove the narrow sticker

from the installation template 

q

and stick it with the fold line 

onto an appropriate place on the
cabinet inside wall (see Fig. 1).
When installing the lock in dra-
wers, place the installation templa-
te 

q 

on the upper inside drawer

wall at the height of the grip or
knob. 

1b. Mark the two new screw holes for

the lock plate 

r

with a sharp object

(such as a nail). While closing the
door, mark the position of the instal-
lation template 

q

on the narrow

part of the inside of the door using a
pencil. Carefully remove the installa-
tion template 

q

from the inside ca-

binet wall. 

2. Pull off the back of the sticker 

.

Stick the installation template 

q

onto the previously marked position,
flush against the inside edge of the
door using the sticker 

(see Fig. 2).

3. Smooth out the installation tem-

plate 

q

and mark four of the six

screw holes 

(X) (two above and

two below) for the lock 

w

.

Fig. 1

q

w

e

r

t

y

u

i

o

a

Fig. 2

D