Справочник Пользователя для FMI CGDV32PR
www.fmiproducts.com
116646-01J
17
VENTING INSTallaTION
Continued
Number Description
VKC-58
VKC-58
Corner Vent Kit, Galvanized
(Includes 45° Elbow, 7"-12"
Adjustable Pipe, Wall Firestop,
Horizontal Termination, 6" Pipe,
90° Elbow, 18 Screws)
(Includes 45° Elbow, 7"-12"
Adjustable Pipe, Wall Firestop,
Horizontal Termination, 6" Pipe,
90° Elbow, 18 Screws)
HHTK-58 High Wind Round Horizontal Termi-
nation Kit (Includes Round Termina-
tion, Wall Firestop, 45° Elbow)
tion, Wall Firestop, 45° Elbow)
HHT-58
High Wind Round Termination
Kit, Galvanized
Kit, Galvanized
HTK-58
Horizontal Round Termination
Kit (Includes Round Termination,
Wall Firestop, 45° Elbow)
Kit (Includes Round Termination,
Wall Firestop, 45° Elbow)
HT-58
Horizontal Round Termination,
Galvanized
Galvanized
HTS-58
Horizontal Square Termination,
Galvanized
Galvanized
HTKS-58 Horizontal Square Termination
Kit (Includes: Square Termina-
tion, Wall Firestop, 45° Elbow)
tion, Wall Firestop, 45° Elbow)
HTS-58
Horizontal Square Termination,
Galvanized
Galvanized
VT-58
Vertical Round Termination,
Galvanized
Galvanized
FIREplaCE INSTallaTION
Figure 26 - Blower Model BK
Magnetic
Strips
Strips
Exhaust
Port
Port
Screw
Green
Ground
Wire
Ground
Wire
Spade
Terminals
Terminals
Side View
Lower Firebox
Cavity
Blower
Location
Location
Number Description
ST-58-14 14" Snorkel Termination, Galva-
ST-58-14 14" Snorkel Termination, Galva-
nized
ST-58-36 36" Snorkel Termination, Galvanized
SC-58
SC-58
Storm Collar, Galvanized
WF-58
Wall Firestop, Galvanized
RF-58-6 Roof Flashing - 0 to 6/12 Pitch,
Galvanized
RF-58-12 Roof Flashing - 6/12 to 12/12
Pitch, Galvanized
VR-58
Vertical Restrictor, Galvanized
S-58
Vinyl Siding Standoff, Galvanized
WS-58
Wall Strap
CS-58
Cathedral Ceiling Support
FP-58
Firestop Plate
SF-58
Stucco Flashing - For use with
HTS-58
HTS-58
RF-58
Flat Roof Flashing
PF58-927 Flex Pipe Section 9" to 24"
PF58-1236 Flex Pipe Section 12" to 36"
PF58-1854 Flex Pipe Section 18" to 54"
VKF58-927 Flex Kit (Includes Flex Pipe Wall
PF58-1236 Flex Pipe Section 12" to 36"
PF58-1854 Flex Pipe Section 18" to 54"
VKF58-927 Flex Kit (Includes Flex Pipe Wall
Section 9" to 27", Firestop and
Horizontal Square Termination)
Horizontal Square Termination)
CHECK GAS TYPE
Use proper gas type for fireplace unit you are
installing. If your gas supply is not correct, do
not install fireplace. See retailer where you
purchased fireplace for proper fireplace ac-
cording to your gas type or to purchase gas
conversion kit (see Accessories, page 37).
installing. If your gas supply is not correct, do
not install fireplace. See retailer where you
purchased fireplace for proper fireplace ac-
cording to your gas type or to purchase gas
conversion kit (see Accessories, page 37).
INSTALLING OpTIONAL bLOWER
ACCESSORY
ACCESSORY
NOTICE: If installing blower in
an existing fireplace with gas
connections, shut off gas sup-
ply and disconnect heater from
gas supply. Contact a qualified
service person to do this.
WARNING: If there is a duplex
electrical outlet installed in the
right side of the bottom of the
fireplace base area, be sure that
the electrical power to the outlet is
turned off before proceeding with
blower installation. Failure to do
this may result in serious injury.
Model BK Installation
Follow all instructions provided in blower
accessory kit.
1. Attach power cord to blower motor by
Follow all instructions provided in blower
accessory kit.
1. Attach power cord to blower motor by
firmly pushing two female terminals at end
of power cord onto two spade terminals
on blower motor (see Figure 26).
of power cord onto two spade terminals
on blower motor (see Figure 26).
2. Attach green ground wire from power cord
to blower housing using screw provided
(see Figure 26). Tighten screws securely.
(see Figure 26). Tighten screws securely.
3. Place blower against lower rear wall of
firebox outer wrapper with exhaust port
directed upward. Blower will fit inside back
opening and be held in position against
back wall by magnets (see Figure 26).
directed upward. Blower will fit inside back
opening and be held in position against
back wall by magnets (see Figure 26).