Справочник Пользователя для INSTEON 2442-522 (aus-nz)
Page 21 of 24
2442-222/2442-422/2442-522 - Rev: 1/21/2014 8:00 AM
light with another
controller, the light will
turn on, then back off
controller, the light will
turn on, then back off
with an INSTEON on-level at
a high brightness and an X10
address on-level at a low
brightness
a high brightness and an X10
address on-level at a low
brightness
Remove the X10 address from INSTEON
controller
controller
When I press a button on
Micro module, it takes a
long time for other
INSTEON devices it is
controlling to respond
Micro module, it takes a
long time for other
INSTEON devices it is
controlling to respond
Micro module is trying to
control a responder that is not
responding and may have
been removed
control a responder that is not
responding and may have
been removed
Connect power to the responder
If the INSTEON device is still available,
remove it from Micro module and then re-add it
remove it from Micro module and then re-add it
Perform a factory reset
The load is buzzing when
on or dim.
on or dim.
The dimming component
inside Micro module “chops”
the power line sine wave to
reduce the power
inside Micro module “chops”
the power line sine wave to
reduce the power
The bulb filaments are vibrating. Use rough-
service, or appliance grade bulbs to reduce the
noise
service, or appliance grade bulbs to reduce the
noise
Run Micro module in the “full-on” mode or
switch to a non-dimming Micro On/Off module
switch to a non-dimming Micro On/Off module
Micro module is locked up
A surge or excessive noise
on the power line occurred
on the power line occurred
Power cycle Micro module
Perform a factory reset
Micro module is getting
warm to the touch
warm to the touch
It is normal for dimmers to get
warm (Micro module
conforms to safety standards)
warm (Micro module
conforms to safety standards)
Micro module will dissipate about 1 watt per
100 watts of load. Using metal junction boxes,
removing insulation around the outside of the
box and controlling a smaller load will all help
lower the temperature.
100 watts of load. Using metal junction boxes,
removing insulation around the outside of the
box and controlling a smaller load will all help
lower the temperature.
Micro module blinks green
one time after it is
activated
one time after it is
activated
Micro module supports an
error blink feature. A green
blink indicates that all
responders are
communicating properly
error blink feature. A green
blink indicates that all
responders are
communicating properly
You may disable error blink via software if
desired
desired
Micro module blinks red
one time after it is
activated
one time after it is
activated
Micro module supports an
error blink to let you know
that a responder did not
acknowledge the command
and that there is a lot of
unacknowledged
communications on the
network
error blink to let you know
that a responder did not
acknowledge the command
and that there is a lot of
unacknowledged
communications on the
network
Confirm that the responder is powered and
available. If you don’t want this device to be a
responder you can unlink it if available or use
software to remove the link. Once the issue is
resolved, you may disable error blink via
software if desired.
available. If you don’t want this device to be a
responder you can unlink it if available or use
software to remove the link. Once the issue is
resolved, you may disable error blink via
software if desired.
Micro module can turn off
my responder, but nothing
happens when I send an
on
my responder, but nothing
happens when I send an
on
Responder’s scene level is
off
off
Add responder to scene again at desired
scene on-level
scene on-level
Micro module still controls
devices even after factory
reset
devices even after factory
reset
The responder’s link was not
removed prior to Micro
module factory reset (called a
half-link)
removed prior to Micro
module factory reset (called a
half-link)
Remove responder from Micro module