Руководство По Работе для Panasonic DMREX768EB

RQT9167

Ref

erence

Cannot operate the TV with unit’s
remote control.

 Change the manufacturer code on the remote control.

 It may be necessary to set the code on the remote control again after

changing the batteries.

The remote control doesn’t work.

 The remote control code is wrong. Change to the correct code.

 The batteries are depleted. Replace them with new ones.

 Point the remote control at the remote control sensor on the main unit.

 Remove obstacles between the remote control and the main unit.

−

 Remove dust from the transmission window and the unit’s sensor.

−

 Coloured glass may obstruct the signal reception/transmission.

−

 Don’t place the signal sensor in direct sunlight or in areas that may be

subject to sun exposure.

−

 It may be necessary to set the manufacturer code again after changing the

batteries.

 The Child Lock function is activated.

The unit is on but cannot be
operated.

 Recording drive or playback drive has not been selected properly.

19, 20

 Some operations may be prohibited by the disc.

−

 The unit is warm (“U59” appears on the unit’s display). Wait until “U59”

disappears.

 One of the unit’s safety devices may have been activated.

Reset the unit as follows:
Press [

/I] on the main unit to switch to standby mode.

If the unit doesn’t switch to standby mode, reset the unit (

¼ 75, “To restore

the unit if it freezes”).

 The unit cannot be operated while performing an update. “SW-DL” appears on

the unit’s display while it is updating. Please wait until the “SW-DL” disappears.

−

“U88” is displayed and the disc
cannot be ejected.

 The unit is carrying out the recovery process. The disc may be defective.

Do the following to eject the disc. Try another disc.
(1) Press [

/I] on the main unit to switch to standby mode.

If the unit doesn’t switch to standby mode, reset the unit (

¼ 75, “To

restore the unit if it freezes”).

(2) While the unit is turned off, press and hold [

] and [CH ] on the main

unit at the same time for about 5 seconds. (Ejection may take extra
time depending on discs.)

−

Cannot eject a disc.

 The unit is recording.

−

 The unit may have a problem. Eject the disc as in (2) above.
 Linked timer recordings with external equipment is in recording standby

(“EXT-L” on the unit’s display blinks when [

DVD] is pressed.) Press [EXT

LINK] to cancel the recording standby.
If the Child Lock function is activated, above operation does not work.
Cancel the Child Lock function.

−

27, 67

Startup is slow.

 Startup takes time in the following situations:

–  A disc other than a DVD-RAM is inserted.
–  The clock is not set.
–  Immediately after a power failure or the AC mains lead is connected.
–  When the unit is connected with an HDMI cable.

 When “Power Save” is set to “Off”, startup becomes faster than when

“Power Save” is “On”.

−

General Issues

Operation

Page

General Issues

GUIDE Plus+

The GUIDE Plus+ system does not
receive any data.

 Check whether the clock is properly set.
 If signal quality is bad (ghost images or limited reception), the GUIDE

Plus+ system may not be able to receive any data.

−

“No Data” is displayed for some or
all stations.

 Some stations are not supported by the GUIDE Plus+ system.
 Programme the Timer recording manually.

−

The GUIDE Plus+ information is
not displayed properly.

 There was a programme change or GUIDE Plus+ information from a

broadcast station was possibly not correctly transmitted.
Check the current programme, e.g. on the Web site for the GUIDE Plus+
system provider or station provider.

−

(Continued on the next page)

Page

DMR-EX768EB.indb 77

2008/03/06 10:03:25