Руководство По Работе для Panasonic SCPTX7
RQ
T
8
9
2
7
101
Troubleshooting guide
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the
solutions indicated in the chart do not solve the problem, consult your dealer for instructions.
solutions indicated in the chart do not solve the problem, consult your dealer for instructions.
(Continued on the next page)
General Issues
Power
Page
No power.
≥Insert the AC mains lead securely into the household mains socket.
15
The unit is automatically
switched to the standby
mode.
switched to the standby
mode.
≥When “Auto Power Off Mode” is set to “On”, the unit automatically switches
to standby after approximately 10 minutes in the stop mode.
88
When the AC mains lead is
plugged in, “– – – –”
flashes on the unit display.
plugged in, “– – – –”
flashes on the unit display.
≥Last time you used the unit, was the AC mains lead removed from the
power outlet immediately after the unit was turned off, or while “– – – –”
was flashing on the unit display? Conversion and analysis was aborted
while the unit was in standby mode. The unit is converting and analysing
the tracks again. While “– – – –” is flashing on the unit display, the unit can
be turned on without any problems.
was flashing on the unit display? Conversion and analysis was aborted
while the unit was in standby mode. The unit is converting and analysing
the tracks again. While “– – – –” is flashing on the unit display, the unit can
be turned on without any problems.
11,
26
The unit display does not
turn off even when the unit
is in “Power-Save Mode”.
turn off even when the unit
is in “Power-Save Mode”.
≥If there are recorded tracks that have not been converted or analysed yet,
the unit will enter standby in “Quick-Start Mode” when the unit is turned off.
Once conversion and analysis is complete, the unit will switch to “Power-
Save Mode”.
Once conversion and analysis is complete, the unit will switch to “Power-
Save Mode”.
26,
88
The unit starts up slower
than it used to when set to
“Power-Save Mode”.
than it used to when set to
“Power-Save Mode”.
≥When the number of tracks recorded to the HDD increases, it will take
more time for the unit to start up.
—
I set the unit to “Quick-
Start Mode”, but it starts
up slow.
Start Mode”, but it starts
up slow.
≥In some cases, the unit manages the system for stable operation for
several tens of seconds while the unit is turned off. During this period, if the
unit is turned on, it can take time to start up (“Starting now. Please wait” is
displayed). Furthermore, during system management, the standby
indicator (red) will turn off briefly and a “click” sound may be heard.
unit is turned on, it can take time to start up (“Starting now. Please wait” is
displayed). Furthermore, during system management, the standby
indicator (red) will turn off briefly and a “click” sound may be heard.
—
General Issues
Operation
The main unit is hot.
≥When this unit is used for an extended period of time, the main unit can
become hot. However, this does not cause any harm to the unit.
—
The display is dim.
≥Change “FL Dimmer” in “Power On/Off” menu.
88
No response when any
buttons pressed.
buttons pressed.
≥This unit cannot play discs other than the ones listed in these operating
instructions.
≥The unit may not be operating properly due to lightning, static electricity, or
other external factors. Turn the unit off and on again. Alternatively, turn the
unit off, disconnect the AC mains lead, and then reconnect it.
unit off, disconnect the AC mains lead, and then reconnect it.
≥Condensation has formed: Wait 1 to 2 hours for it to evaporate.
≥Have you created a backup or restored the HDD? Backup and restore can
≥Have you created a backup or restored the HDD? Backup and restore can
take some time to complete.
≥Press and hold [Í/I] on the main unit for approximately 10 seconds to
force the unit to restart.
20
—
—
—
—
—
No response when remote
control buttons pressed.
control buttons pressed.
≥Check that the batteries are installed correctly.
≥The batteries are depleted: Replace them with new ones.
≥Point the remote control at the remote control signal sensor and operate.
≥The batteries are depleted: Replace them with new ones.
≥Point the remote control at the remote control signal sensor and operate.
8
8
8
8
8
When using the remote
control, the message
“Please set your remote
control to Mode 1 (or 2).” is
displayed.
control, the message
“Please set your remote
control to Mode 1 (or 2).” is
displayed.
≥The remote control settings are not correctly set with this unit’s settings.
Change the mode on the remote control.
90
Using remote controls for
other devices causes
accidental operation on
this unit.
other devices causes
accidental operation on
this unit.
≥Are you using other Panasonic products at the same time? The remote
control signals may be similar, so change the remote control mode.
90
No on-screen display.
≥Select “On” in “On-Screen Messages” in “Display” menu.
87
No picture or sound.
≥Check the video or audio connection.
≥Check the power or input setting of the connected equipment.
≥Check that the disc has something recorded on it.
≥Check that the disc has something recorded on it.
14, 15,
91– 93
91– 93
—
—
—
Re
fe
re
nc
e
U
s
eful
inf
o
rma
tion
PTX7EB.book Page 101 Monday, March 12, 2007 10:13 AM