Руководство По Работе для Panasonic KX-PRS110
32
Programiranje
•
Ako sve prijavljene slušalice počnu
zvoniti, ponovno pritisnite [ ] da biste
to zaustavili, zatim ponovite ovaj korak.
4
Slušalica:
[OK] → → Pričekajte dok se ne prikaže
"
Base PIN" (PIN baze). → Unesite PIN
bazne stanice (zadano: "
0000"). → [OK]
•
Ako ste zaboravili PIN, obratite se
najbližem ovlaštenom servisnom centru.
Odabir bazne stanice
Kada je odabrano "
Auto", slušalica
automatski koristi sve dostupne bazne
stanice na koje je prijavljena. Kada je
odabrana određena bazna stanica, slušalica
poziva i prima pozive koristeći samo tu baznu
stanicu. Ako je slušalica izvan dometa te
bazne stanice, nije moguće izvršavati pozive.
1
[Menu] (desna tipka za programiranje)
2
: Odaberite broj željene bazne stanice
ili "
Auto". → [OK]
Odjavljivanje slušalice
Slušalica može poništiti vlastitu prijavu u
baznoj stanici ili ostale slušalice prijavljene na
istoj baznoj stanici. To omogućuje slušalici da
prekine bežičnu vezu sa sustavom.
1
[Menu] (desna tipka za programiranje)
•
Prikazuju se brojevi svih slušalica
prijavljenih na baznoj stanici.
2
: Odaberite slušalicu koju želite
poništiti. →
[OK]
3
: "
Yes" (Da) → [OK]
4
Poništavanje bazne stanice
Slušalica može poništiti baznu stanicu na koju
je prijavljena. To omogućuje baznoj stanici da
prekine svoju bežičnu vezu sa sustavom.
1
[Menu] (desna tipka za programiranje)
2
: Odaberite baznu stanicu koju želite
poništiti. →
[OK]
3
: "Yes" (Da) →
[OK] →
Povećavanje dometa bazne
stanice
Možete povećati domet signala bazne stanice
koristeći DECT-odašiljač. Koristite isključivo
Panasonicov DECT-odašiljač naveden na 3.
str. Za detalje se obratite svom prodavaču
Panasonica.
Važno:
Važno:
•
Prije prijave DECT-odašiljača na baznu
stanicu morate uključiti način rada preko
DECT-odašiljača.
•
Nemojte koristiti više od jednog DECT-
odašiljača istovremeno.
Postavljanje načina rada preko
DECT-odašiljača
1
[Menu] (desna tipka za programiranje)
2
: Odaberite željenu postavku. →
[OK]
→
Prijavljivanje DECT-odašiljača
(KX-A405) na baznu stanicu
Napomena:
•
Koristite DECT-odašiljač koji nije prijavljen
na drugu stanicu. Ako je DECT-odašiljač
prijavljen na drugoj stanici, najprije ga
odjavite, uz pomoć Uputa za upotrebu
DECT-odašiljača.
1
Bazna stanica:
Pritisnite i držite [ ] otprilike 5 sekundi.
2
DECT-odašiljač:
Spojite prilagodnik za izmjenični napon,
zatim pričekajte dok indikator i
indikator ne zasvijetle zeleno.
3
Bazna stanica:
Da biste izašli iz načina za prijavljivanje,
pritisnite [ ].
R
If all registered handsets start ringing,
press M N again to stop, then repeat
this step.
4
Handset:
M
OKN a Wait until “
Base PIN” is
displayed. a Enter the base unit PIN
(default:
“
0000”). a MOKN
R
If you forget your PIN, contact an
authorised service centre.
Selecting a base unit
When
“
Auto” is selected, the handset
automatically uses any available base unit it is
registered to. When a specific base unit is
selected, the handset makes and receives
calls using that base unit only. If the handset is
out of range of that base unit, no calls can be
made.
1
M
MenuN (right soft key) #137
2
MbN
: Select the desired base unit number,
or
“
Auto”. a MOKN
Deregistering a handset
A handset can cancel its own registration to
the base unit, or other handsets registered to
the same base unit. This allows the handset to
end its wireless connection with the system.
1
M
MenuN (right soft key) #131
R
All handsets registered to the base unit
are displayed.
2
MbN
: Select the handset you want to
cancel. a M
OKN
3
MbN
:
“
Yes” a MOKN
4
M
N
Cancelling a base unit
A handset can cancel a base unit that it is
registered to. This allows the base unit to end
its wireless connection with the system.
1
M
MenuN (right soft key) #139
2
MbN
: Select the base unit you want to
cancel. a M
OKN
3
MbN
:
“
Yes” a MOKN a M
N
Increasing the range of the base
unit
You can increase the signal range of the base
unit by using a DECT repeater. Please use
only the Panasonic DECT repeater noted on
page 3. Contact your Panasonic dealer for
details.
Important:
R
Important:
R
Before registering the DECT repeater to
this base unit, you must turn the DECT
repeater mode on.
R
Do not use more than one DECT repeater
at a time.
Setting the DECT repeater mode
1
M
MenuN (right soft key) #138
2
MbN
: Select the desired setting. a M
OKN
a
M
N
Registering the DECT repeater
(KX-A405) to the base unit
Note:
R
R
Please use a DECT repeater that has not
yet been registered to another unit. If the
DECT repeater is registered to another unit,
deregister it first, referring to the Installation
Guide for the DECT repeater.
1
Base unit:
Press and hold M N for about 5 seconds.
2
DECT repeater:
Connect the AC adaptor, then wait until
the indicator and indicator light
green.
3
Base unit:
To exit the registration mode, press M N.
32
Programming
PRS110FX(en)_0725_ver020.pdf 32
2013/07/25 9:56:13
R
If all registered handsets start ringing,
press M N again to stop, then repeat
this step.
4
Handset:
M
OKN a Wait until “
Base PIN” is
displayed. a Enter the base unit PIN
(default:
“
0000”). a MOKN
R
If you forget your PIN, contact an
authorised service centre.
Selecting a base unit
When
“
Auto” is selected, the handset
automatically uses any available base unit it is
registered to. When a specific base unit is
selected, the handset makes and receives
calls using that base unit only. If the handset is
out of range of that base unit, no calls can be
made.
1
M
MenuN (right soft key) #137
2
MbN
: Select the desired base unit number,
or
“
Auto”. a MOKN
Deregistering a handset
A handset can cancel its own registration to
the base unit, or other handsets registered to
the same base unit. This allows the handset to
end its wireless connection with the system.
1
M
MenuN (right soft key) #131
R
All handsets registered to the base unit
are displayed.
2
MbN
: Select the handset you want to
cancel. a M
OKN
3
MbN
:
“
Yes” a MOKN
4
M
N
Cancelling a base unit
A handset can cancel a base unit that it is
registered to. This allows the base unit to end
its wireless connection with the system.
1
M
MenuN (right soft key) #139
2
MbN
: Select the base unit you want to
cancel. a M
OKN
3
MbN
:
“
Yes” a MOKN a M
N
Increasing the range of the base
unit
You can increase the signal range of the base
unit by using a DECT repeater. Please use
only the Panasonic DECT repeater noted on
page 3. Contact your Panasonic dealer for
details.
Important:
R
Important:
R
Before registering the DECT repeater to
this base unit, you must turn the DECT
repeater mode on.
R
Do not use more than one DECT repeater
at a time.
Setting the DECT repeater mode
1
M
MenuN (right soft key) #138
2
MbN
: Select the desired setting. a M
OKN
a
M
N
Registering the DECT repeater
(KX-A405) to the base unit
Note:
R
R
Please use a DECT repeater that has not
yet been registered to another unit. If the
DECT repeater is registered to another unit,
deregister it first, referring to the Installation
Guide for the DECT repeater.
1
Base unit:
Press and hold M N for about 5 seconds.
2
DECT repeater:
Connect the AC adaptor, then wait until
the indicator and indicator light
green.
3
Base unit:
To exit the registration mode, press M N.
32
Programming
PRS110FX(en)_0725_ver020.pdf 32
2013/07/25 9:56:13
R
If all registered handsets start ringing,
press M N again to stop, then repeat
this step.
4
Handset:
M
OKN a Wait until “
Base PIN” is
displayed. a Enter the base unit PIN
(default:
“
0000”). a MOKN
R
If you forget your PIN, contact an
authorised service centre.
Selecting a base unit
When
“
Auto” is selected, the handset
automatically uses any available base unit it is
registered to. When a specific base unit is
selected, the handset makes and receives
calls using that base unit only. If the handset is
out of range of that base unit, no calls can be
made.
1
M
MenuN (right soft key) #137
2
MbN
: Select the desired base unit number,
or
“
Auto”. a MOKN
Deregistering a handset
A handset can cancel its own registration to
the base unit, or other handsets registered to
the same base unit. This allows the handset to
end its wireless connection with the system.
1
M
MenuN (right soft key) #131
R
All handsets registered to the base unit
are displayed.
2
MbN
: Select the handset you want to
cancel. a M
OKN
3
MbN
:
“
Yes” a MOKN
4
M
N
Cancelling a base unit
A handset can cancel a base unit that it is
registered to. This allows the base unit to end
its wireless connection with the system.
1
M
MenuN (right soft key) #139
2
MbN
: Select the base unit you want to
cancel. a M
OKN
3
MbN
:
“
Yes” a MOKN a M
N
Increasing the range of the base
unit
You can increase the signal range of the base
unit by using a DECT repeater. Please use
only the Panasonic DECT repeater noted on
page 3. Contact your Panasonic dealer for
details.
Important:
R
Important:
R
Before registering the DECT repeater to
this base unit, you must turn the DECT
repeater mode on.
R
Do not use more than one DECT repeater
at a time.
Setting the DECT repeater mode
1
M
MenuN (right soft key) #138
2
MbN
: Select the desired setting. a M
OKN
a
M
N
Registering the DECT repeater
(KX-A405) to the base unit
Note:
R
R
Please use a DECT repeater that has not
yet been registered to another unit. If the
DECT repeater is registered to another unit,
deregister it first, referring to the Installation
Guide for the DECT repeater.
1
Base unit:
Press and hold M N for about 5 seconds.
2
DECT repeater:
Connect the AC adaptor, then wait until
the indicator and indicator light
green.
3
Base unit:
To exit the registration mode, press M N.
32
Programming
PRS110FX(en)_0725_ver020.pdf 32
2013/07/25 9:56:13
R
If all registered handsets start ringing,
press M N again to stop, then repeat
this step.
4
Handset:
M
OKN a Wait until “
Base PIN” is
displayed. a Enter the base unit PIN
(default:
“
0000”). a MOKN
R
If you forget your PIN, contact an
authorised service centre.
Selecting a base unit
When
“
Auto” is selected, the handset
automatically uses any available base unit it is
registered to. When a specific base unit is
selected, the handset makes and receives
calls using that base unit only. If the handset is
out of range of that base unit, no calls can be
made.
1
M
MenuN (right soft key) #137
2
MbN
: Select the desired base unit number,
or
“
Auto”. a MOKN
Deregistering a handset
A handset can cancel its own registration to
the base unit, or other handsets registered to
the same base unit. This allows the handset to
end its wireless connection with the system.
1
M
MenuN (right soft key) #131
R
All handsets registered to the base unit
are displayed.
2
MbN
: Select the handset you want to
cancel. a M
OKN
3
MbN
:
“
Yes” a MOKN
4
M
N
Cancelling a base unit
A handset can cancel a base unit that it is
registered to. This allows the base unit to end
its wireless connection with the system.
1
M
MenuN (right soft key) #139
2
MbN
: Select the base unit you want to
cancel. a M
OKN
3
MbN
:
“
Yes” a MOKN a M
N
Increasing the range of the base
unit
You can increase the signal range of the base
unit by using a DECT repeater. Please use
only the Panasonic DECT repeater noted on
page 3. Contact your Panasonic dealer for
details.
Important:
R
Important:
R
Before registering the DECT repeater to
this base unit, you must turn the DECT
repeater mode on.
R
Do not use more than one DECT repeater
at a time.
Setting the DECT repeater mode
1
M
MenuN (right soft key) #138
2
MbN
: Select the desired setting. a M
OKN
a
M
N
Registering the DECT repeater
(KX-A405) to the base unit
Note:
R
R
Please use a DECT repeater that has not
yet been registered to another unit. If the
DECT repeater is registered to another unit,
deregister it first, referring to the Installation
Guide for the DECT repeater.
1
Base unit:
Press and hold M N for about 5 seconds.
2
DECT repeater:
Connect the AC adaptor, then wait until
the indicator and indicator light
green.
3
Base unit:
To exit the registration mode, press M N.
32
Programming
PRS110FX(en)_0725_ver020.pdf 32
2013/07/25 9:56:13