Инструкции Пользователя для Kicker 43CXA600.1
2
CX.1-SERIES AMPLIFIERS
OWNER’S MANUAL
OWNER’S MANUAL
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open
ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill
four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er.
behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open
ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill
four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er.
The KICKER CX Amplifi ers are capable of space-saving vertical mounting. Use a 2.5mm hex key (Allen wrench)
to loosen the end panel, remove the existing brackets, then insert and tighten the double-slotted brackets to the
amplifi er as illustrated on the next page.
to loosen the end panel, remove the existing brackets, then insert and tighten the double-slotted brackets to the
amplifi er as illustrated on the next page.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
Pro Tip: To get the best performance from your new KICKER Amplifi er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
genuine KICKER accessories and wiring.
MODEL:
CXA300.1 | CXA600.1
CXA1200.1 | CXA1800.1
Model:
CXA300.1
CXA600.1 CXA1200.1 CXA1800.1
RMS Power [Watts]
@ 14.4V, 4Ω mono, ≤ 1% THD+N
@ 14.4V, 2Ω mono, ≤ 1% THD+N
@ 14.4V, 4Ω mono, ≤ 1% THD+N
@ 14.4V, 2Ω mono, ≤ 1% THD+N
150W x 1
300W x 1
300W x 1
300W x 1
600W x 1
600W x 1
600W x 1
1200W x 1
1200W x 1
900W x 1
1800W x 1
1800W x 1
Length [in, cm]
8-1/8, 21
8-1/8, 21
12-1/16, 31
13-5/8, 34.6
Specifi cations common to all models:
Height [in, cm]
2-3/8, 6
Width [in, cm]
7-3/16, 18
Frequency Response [Hz]
25–200
Signal-to-Noise Ratio [dB]
>95, A-weighted, re: rated power
Input Sensitivity
Low Level: 125mV–5V
High Level: 250mV–10V
High Level: 250mV–10V
Electronic Crossover
Variable Lo-pass 50Hz–200Hz, 12dB/octave
KickEQ™ Bass Boost
Variable 0–12dB @ 40Hz
Subsonic Filter
25Hz, 24dB/octave
Remote Bass
Yes (sold separately)
WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! Turning up a
system to a level that has audible distortion is more damaging to your ears than listening to an undistorted system at the same
volume level. The threshold of pain is always an indicator that the sound level is too loud and may permanently damage your
hearing. Please use common sense when controlling volume.
2016 CXA Mono Amps Rev F.indd 2
9/24/2015 4:30:48 PM