Инструкции Пользователя для Panamax MB1000
12
RS-232 Communications Protocol & Command Set
BATTERY LEVEL STATUS
Requests the battery level, expressed as a percentage of maxi-
mum (full charge).
Requests the battery level, expressed as a percentage of maxi-
mum (full charge).
Send Query to UPS:
?BATTERYSTAT<CR>
Action:
Load level will be displayed
Response:
$BATTERY = xxx<CR>
xxx is the battery charge level (percentage of maximum charge)
expressed in decimal format. If the value is less than 100, the
hundreds digit is represented with a 0.
expressed in decimal format. If the value is less than 100, the
hundreds digit is represented with a 0.
____________________________________________
LIST CONFIGURATION
Requests a list of all configurable parameters and current settings.
Requests a list of all configurable parameters and current settings.
Send Query to UPS:
?LIST_CONFIG<CR>
Action:
List of configurable parameters and
current settings will be displayed.
Response:
$BTHRESH = level<CR>
$BUZZER
=
mode<CR>
$AVR
=
mode<CR>
$FEEDBACK
=
mode<CR>
LINEFEED
=
mode<CR>
$BRIGHTNESS
=
xxx<CR>
$SCROLL_MODE
=
xxx<CR>
$SLEEP_MODE
=
xxx<CR>
____________________________________________
List of all commands and queries
Send Query to UPS:
?HELP<CR>
Action:
List of all commands and queries
will
be
displayed
Response: !ALL_ON<CR>
!ALL_OFF<CR>
!SWITCH<CR>
!SET_BATTHRESH<CR>
!SET_BUZZER<CR>
!SET_AVR<CR>
!SET_FEEDBACK<CR>
!SET_LINEFEED<CR>
!RESET_ALL<CR>
!ALL_OFF<CR>
!SWITCH<CR>
!SET_BATTHRESH<CR>
!SET_BUZZER<CR>
!SET_AVR<CR>
!SET_FEEDBACK<CR>
!SET_LINEFEED<CR>
!RESET_ALL<CR>
!SET_BRIGHT<CR>
?VOLTAGE<CR>
!SET_SCROLLMODE<CR> ?LOADSTAT<CR>
!SET_SLEEPMODE<CR> ?BATTERYSTAT<CR>
?ID<CR>
?LIST_CONFIG<CR>
?OUTLETSTAT<CR>
?HELP<CR>
?POWERSTAT<CR>
_________________________________________
RESPONSES & MESSAGES
OUTLET STATUS CHANGE
CONDITION
RESPONSE
Outlet Bank 1 changes state $BANK1 = status<CR>
Outlet Bank 2 changes state $BANK2 = status<CR>
Outlet Bank 2 changes state $BANK2 = status<CR>
status = {ON, OFF}
_________________________________________
POWER BUTTON STATUS CHANGE
CONDITION
RESPONSE
Power Button changes
$BUTTON = status<CR>
ON/OFF status
status = {ON, OFF}
status = {ON, OFF}
_________________________________________
POWER FAULT STATUS CHANGE
CONDITION
RESPONSE
Overvoltage State
$PWR = OVERVOLTAGE<CR>
Undervoltage State
$PWR = UNDERVOLTAGE<CR>
Lost Power State
$PWR = LOST POWER<CR>
Test Mode
$PWR = TEST<CR>
Recovery Mode
$PWR = RECOVERY<CR>
Normal Operation Mode
$PWR = NORMAL<CR>
Low Battery
$LOWBAT<CR>
AVR Stage
$AVRSTATE = state<CR>
state = {BOOST, BUCK}
Remaining Backup Time
$TIME = xxx<CR>
xxx = backup time
Battery State
Battery State
$BATTSTATE = xxx<CR>
xxx = {CHARGE, DISCHARGE, FULL}
Power Control Software
Complete Instructions are available by clicking on Help on the
Power Control Software welcome screen.
Complete Instructions are available by clicking on Help on the
Power Control Software welcome screen.