Инструкции Пользователя для TEAC TN-400S

 

o

If the stylus becomes bent (damaged), it will no longer 
be able to accurately trace the groove. Since a bent stylus 
could also damage records and cause malfunction, handle 
styluses carefully.

 

o

Always use a commercially-available stylus cleaner to clean 
a stylus. Use of anything other than a stylus cleaner could 
damage the stylus.

If the tip of the stylus becomes worn, not only will it worsen 
the sound quality, it could also damage records. After about 
300 hours of playback time, replace the stylus with one that 
we specify.

Please use an Audio-Technica ATN100E replacement stylus.

 

o

The cartridge installed in this unit is equivalent to the Audio-
Technica AT100E VM Type cartridge. (The replacement stylus 
for the installed cartridge is green. It does not have an Audio-
Technica mark.)

VM type cartridges have the same characteristics as MM 
type cartridges.

 

o

Follow the replacement instructions in the manual of the 
replacement stylus.

 

o

Since loud noises could suddenly occur, put the unit into 
standby before changing the stylus.

 

o

Be careful not to hurt your hand or the equipment.

 

o

Be careful not to allow small children to accidentally swal-
low styluses.

 

o

Be aware that bent styluses, for example, that result from 
insufficient customer caution or an outside cause are not 
covered by the warranty.

A

N

T I

– S K A T IN

G

3

0

Place records centered on the turntable (platter).

Use this to raise and lower the tip of the stylus.
We recommend using the arm lifter to avoid damaging 
records and styluses, because it is safer and more certain 
than using a finger to do so. 

This is a rest for the tone arm. Before starting to play a 
record, shift the clasp to the right to remove it.

Select the rotation speed indicated on the record to be 
played.

This is a universal type that allows the cartridge to be 
changed easily.

Grounding terminal (|)

Use the grounding wire of the included RCA audio cable 
to connect this connector to the grounding terminal of 
the amplifier, for example.

 

o

This is NOT an electrical safety ground.

If noise from speakers is conspicuous
If connecting the grounding wire of the audio cable 
to the grounding terminal of this unit does not reduce 
noise, disconnect the grounding wire and check the 
sound again. Use the method (connected/disconnected) 
that has the least noise.

These output analog audio signals.
The PHONO EQ switch setting changes the type of out-
put signal.
Use the included audio cable (or commercially-available 
ones) to connect other equipment to the output connec-
tors of this unit.

Signals that have been amplified by the built-in 
equalizer amp are output from the analog audio out-
put connectors (L/R).

The MC or MM cartridge signal is output directly 
through the analog audio output connectors (L/R).
Connect to a device with phono inputs, such as a 
phono equalization preamplifier or an amplifier with 
phono input connectors.

 

o

When shipped new from the factory, this is set to ON.

 

o

Set this to ON if a device is connected to the USB 
port.

When set to ON, if connected to the PHONO inputs of 
an amplifier, for example, the output from speakers and 
headphones will be very loud, which could damage 
equipment or harm hearing.

|

When PHONO EQ is ON

Connect to line input connectors of 
amplifier, etc.

When PHONO EQ is THRU

Connect to phono input connectors of 
amplifier, etc.

Included AC adapter
(GPE053A-V120050-Z)

V

 

o

Do not plug the unit in until after making all connections.

 

o

Carefully read the manuals of the devices that you are 
connecting and follow their instructions when making 
connections.