Справочник Пользователя для Graupner GmbH & Co. KG MC-20
270 Programming examples - Winged models
Initial steps for the programming of a new model
Example: Winged model with two ailerons and – initially – without motor propulsion
In the context of initial commissioning a new
transmitter, in the selection menu …
transmitter, in the selection menu …
»General basic settings«
(page 256)
Battery type
Battery warning
Touch Sense
Top LCD contrast
Li-Io
Display light
Region
2
3.60V
0
EURO
unlim
G E N E R A L B A S I C S E T T I N G S
Owners name
H-J Sandbrunner
Pre-set stick mode
1
Pre-set DSC Output
PPM10
Pre-set Pitch min
rear
Stick warning
unlim
Pre-set modulation
Own phase name
Own phase name
HoTT
2
10
Bottom LCD contrast
0
Own phase name
1
Voice volume
Vario volume
Touch-beeps vol.
7
fr –––
SEL
SEL
7
fr –––
7
fr –––
Power-on/off beep
yes
… some basic information should be entered. This
serves various purposes:
The fi rst three lines of this menu can be used to
individually regulate, in increments between 0 and
10, the volume of voice and signal output emitted via
the built-in loudspeakers or the transmitter's headset
connector. The fourth line of this menu is used to
serves various purposes:
The fi rst three lines of this menu can be used to
individually regulate, in increments between 0 and
10, the volume of voice and signal output emitted via
the built-in loudspeakers or the transmitter's headset
connector. The fourth line of this menu is used to
record the transmitter owner's name and the lines
"Pre-set stick mode", "Pre-set modulation", "Pre-
set DSC Output" and "Pre-set Pitch min" are for the
storage of pre-set values used as defaults for new
models. These are then adopted on the activation of
a new model memory in its basic settings, but can be
changed there at any time.
The "Top / Bottom LCD Contrast" lines can be
used to adapt the contrast of respective displays to
ambient light conditions as necessary by changing
the standard pre-set "0" in a range of ±20 (as an
alternative to the line with the same name in the
»Secret mode« menu page 32).
The setting in the "Display light" line determines
how long display lighting remains illuminated after
the transmitter is switched on or after the last key
actuation.
The selection of "yes/no" in the "Power-on/off beep"
line determines whether the "recognition melody" is
to sound when the transmitter is switched off or on
again.
The "Battery type" line indicates to the transmitter
whether its power comes from a four-cell NiMH
battery or a single-cell LiPo battery and the "Battery
warning" line can be used to individually set the
threshold for the battery warning. Make sure that you
do not enter a value which is too low, so that you still
have suffi cient time to safely land your model in the
event of a battery warning.
If necessary, the "Stick warning" line can be used to
determine how long the transmitter should wait after the
last activation of an operating element before issuing
a visual and acoustic stick warning, followed about a
minute later by the transmitter switching itself off.
On the other hand, the setting made in the "Touch
Sense" line is merely a personal comfort setting. The
lower this number is, the more sensitive the touch
pad will be to taps and vice versa.
"Pre-set stick mode", "Pre-set modulation", "Pre-
set DSC Output" and "Pre-set Pitch min" are for the
storage of pre-set values used as defaults for new
models. These are then adopted on the activation of
a new model memory in its basic settings, but can be
changed there at any time.
The "Top / Bottom LCD Contrast" lines can be
used to adapt the contrast of respective displays to
ambient light conditions as necessary by changing
the standard pre-set "0" in a range of ±20 (as an
alternative to the line with the same name in the
»Secret mode« menu page 32).
The setting in the "Display light" line determines
how long display lighting remains illuminated after
the transmitter is switched on or after the last key
actuation.
The selection of "yes/no" in the "Power-on/off beep"
line determines whether the "recognition melody" is
to sound when the transmitter is switched off or on
again.
The "Battery type" line indicates to the transmitter
whether its power comes from a four-cell NiMH
battery or a single-cell LiPo battery and the "Battery
warning" line can be used to individually set the
threshold for the battery warning. Make sure that you
do not enter a value which is too low, so that you still
have suffi cient time to safely land your model in the
event of a battery warning.
If necessary, the "Stick warning" line can be used to
determine how long the transmitter should wait after the
last activation of an operating element before issuing
a visual and acoustic stick warning, followed about a
minute later by the transmitter switching itself off.
On the other hand, the setting made in the "Touch
Sense" line is merely a personal comfort setting. The
lower this number is, the more sensitive the touch
pad will be to taps and vice versa.
In contrast, the setting in the "Region" line is anything
but a matter of taste and is determined by statutory
regulations: Therefore, when in France, only
commission the transmitter with the "France"
setting.
The ten "Own phase name" lines can be used to
create one's own phase names, which are then
valid throughout the transmitter, if none of the pre-
set phase names appear appropriate. An entry itself
is accomplished – as also for owner's name – by
switching to a second display page and selecting the
necessary characters from a character list.
This menu can be exited after completing "general
settings" with a return to the multi-function menu by
way of the center
but a matter of taste and is determined by statutory
regulations: Therefore, when in France, only
commission the transmitter with the "France"
setting.
The ten "Own phase name" lines can be used to
create one's own phase names, which are then
valid throughout the transmitter, if none of the pre-
set phase names appear appropriate. An entry itself
is accomplished – as also for owner's name – by
switching to a second display page and selecting the
necessary characters from a character list.
This menu can be exited after completing "general
settings" with a return to the multi-function menu by
way of the center
ESC
key of the left touch pad.
To program a new model, now use the selection keys
of the left or right touch pad to switch to the menu …
of the left or right touch pad to switch to the menu …
"Model select"
(page 69)
…, and use the selection keys of the left or right
touch pad to select a free model memory location.
touch pad to select a free model memory location.
03
04
05
01
06
R16
¿¿¿
free
¿¿¿
¿¿¿
free
¿¿¿
¿¿¿
free
¿¿¿
¿¿¿
free
¿¿¿
00:12h
¿¿¿
free
¿¿¿
02
Right after a tap on the center
SET
key of the right
touch pad to confi rm this selection, the type of model
to be programmed will be requested:
to be programmed will be requested: