Справочник Пользователя для Mitel Deutschland GmbH 68635RFP36U-01
Configuration and Administration
257
•
a provisioning certificate server through OMP
System -> Provisioning -> Certificates server tab
(see section 6.5.5.3)
The OMM provides the local certificate chain and the private key to servers requesting mutual
authentication. The private key file may be password protected.
authentication. The private key file may be password protected.
The system credentials can be inherited if specific sources for configuration and resource files are
configured, where the ‘Use common certificate configuration’ option is enabled.
configured, where the ‘Use common certificate configuration’ option is enabled.
7.10.4 CERTIFICATE VALIDATION
If the HTTPS or FTPS protocol is used to retrieve files from the configured provisioning server, the OMM
validates the server certificates according to the certificate validation settings.
validates the server certificates according to the certificate validation settings.
You can configure the certificate validation settings via OMP (
System -> Provisioning -> Provisioning
– SSL settings) or the OMM Web service (System -> Provisioning -> Certificates). Certificate
validation settings can also be part of the ConfigURL provided by the RCS or via DHCP.
validation settings can also be part of the ConfigURL provided by the RCS or via DHCP.
If you want to use the same validation settings for a specific URL (i.e., other than the configuration file
URL), enable the “Use common certificate configuration” parameter when configuring the URL (unless
the “Import certificates with first connection” parameter is enabled).
URL), enable the “Use common certificate configuration” parameter when configuring the URL (unless
the “Import certificates with first connection” parameter is enabled).
7.11 RFP 35/36/37 IP / RFP 43 WLAN SOFTWARE UPDATE
The DECT base station checks several locations for a software update. If found, the software is copied
to the flash memory, leaving the current software intact. After successful installation, the OMM is notified
about the new software. Activation of the software is then managed by the active OMM. DECT base
stations that do not have a connection to the OMM activate and start the software immediately.
to the flash memory, leaving the current software intact. After successful installation, the OMM is notified
about the new software. Activation of the software is then managed by the active OMM. DECT base
stations that do not have a connection to the OMM activate and start the software immediately.
Locations for software updates:
•
Attached USB mass storage device with a software image
iprfp3G.dnld in its root directory. The USB
mass storage device must be formatted using the vfat32 file system.
•
If ipdect.cfg supplies the
OM_SwImageUrl variable, the URI is used to get the boot image. Please
see section 7.7.7.
•
TFTP server, path and file configured using the OM Configurator or via DHCP.
•
OMM (SIP-DECT 6.0 or later): If the RFP 35/36/37 IP / RFP 43 WLAN have no valid URL from which
to load the software, they attempt to load the software from the connected OMM. If the OMM is
running on a DECT base station, the RFP OMM delivers the software to the connected base stations.
See section 7.8.7 for more information.
running on a DECT base station, the RFP OMM delivers the software to the connected base stations.
See section 7.8.7 for more information.
7.12 802.1Q SUPPORT
The IP RFPs support VLANs according to IEEE 802.1Q. VLAN can be administered
•
on a per port basis of the LAN switch assuming that the IP RFPs are connected to a single port of a
switched Ethernet environment, or
•
by assigning a VLAN ID to the IP RFP matching the VLAN they should operate in.
VLAN tagging has only to be set to IP RFPs’ in the last case. The whole section refers to that case. With
this, also 802.1p priority within Ethernet frames is enabled.
this, also 802.1p priority within Ethernet frames is enabled.