Листовка для Microsemi PD-AS-951/12-24
Enables powering 12V and 24V terminals via 4-pairs PowerDsine PoE
PowerDsine 951 Splitter
How to power
Cisco 802.11n Aironet 1250
using PowerDsine HiPoE solutions
PD-PS-401G HiPoE Adapter
Allows Cisco 802.11n access points to be fully powered by the
7000G Midspans and supports operation at Gigabit data rates.
When using the PD-PS-401G in the system, both radios in the
WLAN access point operate, providing full coverage.
Allows Cisco 802.11n access points to be fully powered by the
7000G Midspans and supports operation at Gigabit data rates.
When using the PD-PS-401G in the system, both radios in the
WLAN access point operate, providing full coverage.
Product Information
PowerDsine 7000G Family
IEEE 802.3at pre-standard High power Midspan series,
delivers 32W per port, Gigabit support, available in
1-, 6-, 12-, 24-port models with remote management (Optional)
IEEE 802.3at pre-standard High power Midspan series,
delivers 32W per port, Gigabit support, available in
1-, 6-, 12-, 24-port models with remote management (Optional)
PD HiPoE/Cisco Ver 1.0 4/08
International
Tel: +972-9-7755100
Fax: +972-9-7755111
PowerDsine@Microsemi.com
Tel: +972-9-7755100
Fax: +972-9-7755111
PowerDsine@Microsemi.com
India
Tel: +91-22-65529031
India_AMSG@Microsemi.com
Tel: +91-22-65529031
India_AMSG@Microsemi.com
North America
Tel: +1-631-756-4680
Fax: +1-631-756-4691
PowerDsineUSA@Microsemi.com
Tel: +1-631-756-4680
Fax: +1-631-756-4691
PowerDsineUSA@Microsemi.com
Corporate Headquarters
Tel: +1-949-221-7100
Fax: +1-949-756-0308
Tel: +1-949-221-7100
Fax: +1-949-756-0308
Europe
Tel: +44 (0) 208-622-3107
Fax: +44 (0) 208-622-3200
UK_AMSG@Microsemi.com
Tel: +44 (0) 208-622-3107
Fax: +44 (0) 208-622-3200
UK_AMSG@Microsemi.com
Part Number
Name
Description
PD-7006G/AC/M
PowerDsine 7006 Managed
6-port, HiPoE Managed Midspan
PD-7012G/AC/M
PowerDsine 7012 Managed
12-port, HiPoE Managed Midspan
PD-7024G/AC/M
PowerDsine 7024 Managed
24-port, HiPoE Managed Midspan
PD-7001G/AC
PowerDsine 7001
1-port HiPoE Midspan
PD-PS-401G
PowerDsine PD-PS-401G Adapter
HiPoE Adapter
Ordering Information
PowerDsine HiPoE
™
Q
UICK
R
EFERENCE
Power
Data
Overview
PowerDsine’s PD-AS-951 High-Power active splitters enable data
terminals that were not originally designed to accept power from the
Ethernet, to be powered by Power over Ethernet midspans. The PD-
AS-951 High Power splitter (user selectable 12V or 24V) can power
devices such as WiMAX CPEs, small WiMAX base-stations, 802.11n
Access-Points, Thin- Clients, PTZ (Pan/Tilt/Zoom) IP Cameras, Video-
Phones and more.
terminals that were not originally designed to accept power from the
Ethernet, to be powered by Power over Ethernet midspans. The PD-
AS-951 High Power splitter (user selectable 12V or 24V) can power
devices such as WiMAX CPEs, small WiMAX base-stations, 802.11n
Access-Points, Thin- Clients, PTZ (Pan/Tilt/Zoom) IP Cameras, Video-
Phones and more.
High Power Splitter Solution
Many contemporary terminals are designed and deployed without
the ability to accept power via their LAN input. Such devices can only
accept power through their DC jack while their RJ45 input accepts
only data. Moreover, such devices might only accept voltage levels
lower than the PoE standard minimum voltage (44v in IEEE802.3af
/ 50v in 802.3at). Using the PD-AS-951 high power splitter, these
terminals immediately become PoE-ready without any modification
required on their side.
the ability to accept power via their LAN input. Such devices can only
accept power through their DC jack while their RJ45 input accepts
only data. Moreover, such devices might only accept voltage levels
lower than the PoE standard minimum voltage (44v in IEEE802.3af
/ 50v in 802.3at). Using the PD-AS-951 high power splitter, these
terminals immediately become PoE-ready without any modification
required on their side.
The splitter is identified as a powered device (PD) in front of the
powering Midspan and after being detected and powered, it physically
splits the data and power streams, arriving over a single cable, into
two separate cords (LAN & DC) which go directly to the data terminal.
Voltage regulation is also performed to the level required by the
terminal (12V or 24V).
powering Midspan and after being detected and powered, it physically
splits the data and power streams, arriving over a single cable, into
two separate cords (LAN & DC) which go directly to the data terminal.
Voltage regulation is also performed to the level required by the
terminal (12V or 24V).
PoE 951 Splitter Specifications
Connectors
2 x RJ-45, shielded, EIA 568A and 568B
DC Jacks
On unit: O.D x I.D = 2.5 x 6.4 mm
Ext. Cable #1: O.D x I.D = 5.5 x 2.5 mm
Ext. Cable #2: O.D x I.D = 3.4 x 1.4 mm
On unit: O.D x I.D = 2.5 x 6.4 mm
Ext. Cable #1: O.D x I.D = 5.5 x 2.5 mm
Ext. Cable #2: O.D x I.D = 3.4 x 1.4 mm
Data Rate
10/100/1000
Electrical
Pin Assignment & Polarity: 3/6 (+),1/2 (-)
or 4/5 (+),7/8 (-)
Input voltage: 44 - 57 Vdc
Input power: 70W max
Output power: 54W max
Output Current: 5A@12V; 2.5A@24V
Input voltage: 44 - 57 Vdc
Input power: 70W max
Output power: 54W max
Output Current: 5A@12V; 2.5A@24V
Dimensions & Weight
38 mm (H) x 130 mm (W) x 73 mm (D)
(2.2 in x 3.2 in x 1 in)
285 gram (0.63 lbs)
285 gram (0.63 lbs)
Indicators
Output Power Indicators:
Green LED (4-pairs), Yellow LED (2-pairs)
Environmental
Operating Temp: 0 to 40ºC (32º to 104ºF)
Storage Temp: -20º to 70ºC (-4º to 158ºF)
Operating Humidity: 10% to 90%,
Operating Humidity: 10% to 90%,
non-condensing
Storage Humidity: 5% to 95%,
non-condensing
Thermal Rating:
38 BTU/Hr
Reliability
MTBF: 100,000 hours @ 25ºC
Electromagnetic Emissions FCC Part 15 Class A
& Immunity
EN55022 (CISPR 22), Class A
EN55024 (CISPR 24)
EN55024 (CISPR 24)
Regulatory Compliance
CE
Warranty
1-year
Network
Camera
Power & Data
PowerDsine
®
Midspan
PD-951
Splitter
Data
Ethernet Switch