Справочник Пользователя для Advanced Control Technologies Inc. 0677-0X

ZDP100 Instructions
101002

HomePro

0607-01

2

The Lamp Module can be set in a child protect mode by the Wireless Controller. When this mode is active, a user
will have to press the button on the Lamp Module 3 times rapidly to activate the attached load. The module operates
normally when controlled by the Wireless Controller..

The button on the Lamp Module also plays a role as a reset in addition to adding module to groups and scenes.
This is described in more detail in the Wireless Controller instructions.

This Lamp Module is designed to protect itself against loads that exceed it’s maximum power rating.  The
application of a load that exceeds that rating is quickly sensed by the dimmer and it responds by immediately
shutting off all power to that load.

If the dimmer doesn’t seem to work, or if it only works momentarily, check to see that the total lamp wattage doesn’t
exceed the 300W rating of the Lamp Module.  If a properly sized load is restored to the dimmer, it can be operated
normally once again.

The Lamp Module hardware has an over current detection circuit, which is final protection against overload.

If the software fuse should fail to shut down the dimmer when overloaded, backup protection is provided by an
internal fuse.  This fuse is not user serviceable.  Check your home circuit breakers before concluding that the
product must be returned to manufacturer for repair at a nominal charge.

When a light bulb reaches the end of it’s life and burns out, it sometimes creates a momentary short circuit.  The
high current that results may cause the dimmer to properly respond by turning off.   Should this happen, replace
the bulb with a new one.  The dimmer can now be operated to restore power to the light.

Advanced Control Technologies, Inc. gives this expressed warranty (along with extended warranty endorsements, where applicable) in lieu
of all other warranties, express or implied, including (without limitation), warranties of merchantability and fitness for a particular purpose.
This constitutes Advanced Control Technologies, Inc.’s sole warranty and obligation with regard to our products as well as the Customer’s
sole remedy.
Advanced Control Technologies, Inc. expressly disclaims all liability and responsibility for any special, indirect or consequential damages
or any further loss of any kind whatsoever resulting from the use of our product.  The Customer’s sole and exclusive remedy and the limit
of Advanced Control Technologies, Inc.’s liability for any loss whatsoever, shall not exceed the purchase price paid by the Customer for the
product to which a claim is made.
Some states do not allow limitations of incidental or consequential damages or on how long an implied warranty lasts, so the above limitations
may not apply to you.  This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
All products manufactured by Advanced Control Technologies, Inc. are warranted to be free from defects in material and workmanship in
accordance with and subject to the following terms and conditions:

1.  This warranty is limited to the original Customer only.  It cannot be transferred or assigned to third parties unless the intent to

transfer to a third party is expressly indicated in a purchase order and/or warranty processing arrangements have been agreed
upon in writing by Advanced Control Technologies, Inc.

2.  Advanced Control Technologies, Inc. will correct any defects in material or workmanship which appear within one (1) year from the

date of purchase.  Advanced Control Technologies, Inc. will repair or replace, at our option, any defective products, provided that
our inspection discloses that such defects developed under normal and proper use.  This warranty does not extend to goods
subjected to misuse, neglect, accident or improper installation, or to maintenance or repair of products which have been altered or
repaired by anyone except Advanced Control Technologies, Inc. unless otherwise stated in writing.

3.  An appropriate charge (50% of product list price) will be made for testing, repairs, replacement and shipping for returned product

which is not defective or found to be defective as the result of improper use, maintenance or neglect.

4.  Information in our descriptive literature is based on product specifications that are current at the time of publication.  Product

specifications, designs and descriptive literature are subject to change as improvements are introduced.  Although we announce
changes as they occur, we cannot guarantee notification to every Customer.  Advanced Control Technologies, Inc. warrants
delivered product to conform to the most current specifications, designs and descriptive literature.