Справочник Пользователя для Advanced Control Technologies Inc. 0797-01
Evolve LRM-AS Series 300, Rel. 5.1 Instructions
LRM-AS
by Evolve Guest Controls
bottom of the switch will dim the load. When OFF, pressing and holding the bottom of the switch will
cause the load will go to the minimum dim level.
cause the load will go to the minimum dim level.
Note: Upon restoration of power after a power loss, the LRM-AS returns to previous known state.
LED indication
The LED on the LRM-AS will turn ON when the load attached is OFF, to act as a night light. However, the LED
can be user configured to turn ON when the load attached is ON, if so desired.
can be user configured to turn ON when the load attached is ON, if so desired.
Remote Control
The LRM-AS will respond to bASIC and MULTILEvEL commands that are part of the Z-Wave system. Refer to
your controller’s instructions as to whether your controller can transmit those commands.
your controller’s instructions as to whether your controller can transmit those commands.
All On/All Off
The LRM-AS supports the ALL ON/ ALL OFF commands.
The LRM-AS can be set to respond to ALL ON and ALL OFF commands 4 different ways.
Refer to your controller for information on how to set the LRM-AS to operate in the manner you desire. Some
controllers may be only able to set certain settings of ALL ON/ALL OFF response.
The 4 different ways the LRM-AS can be setup to respond to ALL ON and ALL OFF commands are:
The LRM-AS can be set to respond to ALL ON and ALL OFF commands 4 different ways.
Refer to your controller for information on how to set the LRM-AS to operate in the manner you desire. Some
controllers may be only able to set certain settings of ALL ON/ALL OFF response.
The 4 different ways the LRM-AS can be setup to respond to ALL ON and ALL OFF commands are:
•
LRM-AS will not respond to ALL ON or the ALL OFF command.
•
LRM-AS will respond to ALL OFF command but will not respond to ALL ON command.
•
LRM-AS will respond to ALL ON command but will not respond to ALL OFF command.
•
LRM-AS will respond to ALL ON and the ALL OFF command (default).
Configuration
The LRM-AS supports the Configuration command.
The LRM-AS can be configured to operate differently than how it works when you first install it. Using the
Configuration command you can configure the following:
You can use a EHC-100 to send Configuration commands. (Refer to the Setup Menu, Configuration section)
night Light
The LRM-AS can be configured to operate differently than how it works when you first install it. Using the
Configuration command you can configure the following:
You can use a EHC-100 to send Configuration commands. (Refer to the Setup Menu, Configuration section)
night Light
by default, the LED on the LRM-AS will turn OFF when the load attached is turned ON. To make the LED
turn ON when the load attached is turned ON, set parameter 3 to a value of 0.
• parameter No: 3
• Length: 1 Byte
• Valid Values = 0 or 1 (default 1)
turn ON when the load attached is turned ON, set parameter 3 to a value of 0.
• parameter No: 3
• Length: 1 Byte
• Valid Values = 0 or 1 (default 1)
invert Switch
To change the top of the switch to OFF and the bottom of the switch to ON, set parameter 4 to 1.
• parameter No: 4
• Length: 1 Byte
• Valid Values = 0 or 1 (default 0)
• parameter No: 4
• Length: 1 Byte
• Valid Values = 0 or 1 (default 0)
Load Sense:
• parameter No: 29
• Length: 1 Byte
• Valid Values = 0 or 1 (default 1)
• Length: 1 Byte
• Valid Values = 0 or 1 (default 1)
Set this parameter to 0 to disable load sense. Set this parameter to 1 to enable load sense.
Each Configuration Parameter can be set to its default setting by setting the default bit in the Configuration Set
command. See your controller’s instructions on how to do this (and if it supports it).
All Configuration commands will be reset to their default state when the LRM-AS is excluded from the Z-Wave
network by using the controller to reset the node (on the EHC-100 select “SETUP” and scroll to “RESET UNIT”).
Each Configuration Parameter can be set to its default setting by setting the default bit in the Configuration Set
command. See your controller’s instructions on how to do this (and if it supports it).
All Configuration commands will be reset to their default state when the LRM-AS is excluded from the Z-Wave
network by using the controller to reset the node (on the EHC-100 select “SETUP” and scroll to “RESET UNIT”).