Справочник Пользователя для IDT Technology Limited SMS001

1. Press the power button to turn 

on/off the skateboard. The headlights turn on.

2. Press and hold the power button for 3 seconds to turn on/off the remote.
3. Push the 

Go/Stop switch forward to go, release to stop.

4. Double press the power button on the remote to turn 

on/off the headlights.

5. Changing the playing mode by 

Forward/Reverse and High/Low speed switches.

NOTE
• Taillights beam in normal mode; Flash by automatically detect in stop mode.
• Left and right turning indicators will flash and are controlled by Gyroscope automatically 

when turning direction.

Open the App, it will find the skateboard automatically. With the App, you can
• Navigate directions
• Check the power, light, speed status
• Set the horn sound and light colour
• Turn on/off the headlights and taillights
• Control the night lights
NOTE
The navigation indicators on the deck will turn on and indicate the directions when using 

the GPS navigating function.

NOTE: The remote and the skateboard are paired in the factory. If a new remote is 

needed, pair the new remote with the skateboard before using.
1. Turn off the skateboard and the remote.
2. Pull the 

Go/Stop switch as far backwards as it will allow.

3. Turn on the remote. The Signal indicator of the remote flashes quickly.
4. Turn on the skateboard.
5. Release the 

Go/Stop switch. The Signal indicator of the remote lights steady. The 

remote and the skateboard are successfully paired.

Remark

Drive Unit

2x 250 W brushless DC motor at rear 

wheels

at rear wheels

Speed

Normal Speed mode: ≤12 km/h

Setting by 

Remote contro

High speed mode: : ≤32 km/h

Endurance Mileage

Normal mode: ≤10 km
High speed mode: : ≤20 km

Remote Control

BLE 4.0 module connected to Mobile
Pedal and brake control
Forward/Reverse control

Battery

LG MG1 Power battery pack 
36 V 4 Ah (20x 18650 - 3.6 V) (2200 

mAh-10S2P)

Size

800 mm x 255 mm x 114 mm

Recharge Time

2~2.5 hr

Wheel Base

Diameter: 83 mm

Weight

About 6.1 kg

Board Material

Canadian Maple Wood

Max Load

100 kg

Operation Conditions -10 to 60 

0

C

≤85 % R.H.

Storage Condition

-20 to 80 

0

C

≤95 % R.H.

• Do not burn or bury batteries. Do not puncture or crush. Do not disassemble.
• Recycle lithium batteries. Do not dispose of in the trash
• If the electrolyte in the cells should get on your skin, thoroughly wash with soap and 

water.

• If in the eyes, rinse thoroughly with cool water. Immediately seek medical attention.

• The built-in battery may discharge completely after a long period without use. Recharge 

the battery before use.

• The skateboard should never be left unattended while charging.
• Use only the supplied charger and cable for charging.
• Charge batteries on a fireproof surface away from flammable items or liquids.
• Do not charge inside an automobile, especially while driving.
• Follow the instructions for charging. Do not charge longer than recommended. Unplug 

the USB cable when the battery is charged.

• Do not subject the device to excessive force, shock, dust, temperature or humidity.
• Do not immerse the device in water. If you spill liquid over it, dry it immediately with a 

soft, lintfree cloth.

• Do not clean the device with abrasive or corrosive materials.
• Do not tamper with the device’s internal components. Doing so invalidates the warranty.
• Images shown in this manual may differ from the actual display.
• When disposing of this product, ensure it is collected separately for special treatment.
• The contents of this manual may not be reproduced without the permission of the 

manufacturer.

NOTE:The technical specifications for this product and the contents of the user manual 

are subject to change without notice.
NOTE: Features and accessories will not be available in all countries. For more 

information, please contact your local retailer. To download an electronic version of the user 

manual, please visit http://global.oregonscientific.com/customerSupport.php.

Visit our website www.oregonscientific.com  to  learn  more  about  Oregon  Scientific 

products.
For any inquiry, please contact our Customer Service at info@oregonscientific.com.
Oregon Scientific Global Distribution Limited reserves the right to interpret and construe 

any contents, terms and provisions in this user manual and to amend it, at its sole 

discretion, at any time without prior notice. To the extent that there is any inconsistency 

between the English version and any other language versions, the English version 

shall prevail. 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following 

two conditions: (1) This device may not cause harmful interference, and (2) This device 

must accept any interference received, including interference that may cause undesired 

operation.

 WARNING  Changes or modifications not expressly approved by the party responsible 

for compliance could void the user’s authority to operate the equipment.
 NOTE  This equipment has been tested and found to comply with the limits for a Class 

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 

provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not 

installed and used in accordance with the instructions, may cause harmful interference 

to radio communications. However, there is no guarantee that interference will not 

occur in a particular installation. If this equipment does cause harmful interference to 

radio or television reception, which can be determined by turning the equipment off 

and on, the user is encouraged to try to correct the interference by one or more of the 

following measures:
•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected.

•

Consult the dealer or an experienced radio / TV technician for help.

This Class B digital apparatus complies with Canadian ICES-3(B)/NMB-3(B)

The following information is not to be used as contact for support or sales. Please call 

our customer service number (listed on our website at www.oregonscientific.com), or 

on the warranty card for this product for all inquiries instead.

  

Name:

Oregon Scientific, Inc.

Address: 

Centerpointe center 5 centerpointe drive, suite 400 

office no. 11 & 19 Lake oswego, oregon 97035

Telephone No.:

971-204-0378

declare that the product
Product No.:

SMS606

Product Name:

Huger board Mik

Manufacturer:

IDT Technology Limited

Address:

Block C, 9/F, Kaiser Estate, Phase 1, 41 Man Yue St.,
Hung Hom, Kowloon, Hong Kong

Hereby the manufacturer, IDT Technology Limited, declares that  the radio equipment 

type [Huger board Mik (SMS606)] is in compliance with 2014/53/EU Directive. The full 

text of the EU Declaration of Conformity is available at the following internet address : 

www.oregonscientific.com

  

All EU countries, Switzerland and Norway

Pursuant to and in accordance with Article 14 of the Directive 2012/19/EU of 

the  European  Parliament  on  waste  electrical  and  electronic  equipment 

(WEEE), and pursuant to and in accordance with Article 20 of the Directive 

2013/56/EU of the European Parliament on batteries and accumulators and 

waste batteries.

The barred symbol of the rubbish bin shown on the equipment indicates that, at the end 

of its useful life, the product must be collected separately from other waste.
Please note that the batteries/rechargeable batteries must be removed from the 

equipment before it is given as waste. To remove the batteries/accumulators refer to 

the specifications in the user manual. Therefore, any products that have reached the 

end of their useful life must be given to waste disposal centers specializing in separate 

collection of waste electrical
and electronic equipment, or given back to the dealer when purchasing a new WEEE, 

pursuant to and in accordance with Article 14 as implemented in the country.
The adequate separate collection for the subsequent start-up of the equipment sent to 

be recycled, treated and disposal of in an environmentally compatible way contributes 

to preventing possible negative effects on the environment and health and optimizes 

the recycling and reuse of components making up the apparatus.
Abusive disposal of the product by the user involves application of the administrative 

sanctions according to the laws in force.