Справочник Пользователя для Lifescan 512
Getting a blood sample
pg.
16
Prepare the OneTouch
®
Lancing Device
Remove the blue cap and put a
new lancet in the lancing device.
Twist off the protective disk.
Replace the cap and cock the
lancing device.
new lancet in the lancing device.
Twist off the protective disk.
Replace the cap and cock the
lancing device.
Get a drop of blood
Hold the OneTouch
Hold the OneTouch
®
Lancing
Device firmly against your finger.
Press the release button.
Press the release button.
Gently squeeze and/or massage
your fingertip until a round
drop of blood of at least one
microliter (
your fingertip until a round
drop of blood of at least one
microliter (
actual size) forms
on your fingertip.
Applying blood
pg.
28
and reading results
Touch and hold the drop of blood to the narrow
channel in the top edge of the test strip
Blood will be drawn into the test
strip. Keep holding the drop of
blood to the top edge of the test
strip until the confirmation
window is full. The meter will
begin to count down from 5 to 1.
Then, your blood glucose level
appears on the display along
with the unit of measure, and
the date and time of the test.
channel in the top edge of the test strip
Blood will be drawn into the test
strip. Keep holding the drop of
blood to the top edge of the test
strip until the confirmation
window is full. The meter will
begin to count down from 5 to 1.
Then, your blood glucose level
appears on the display along
with the unit of measure, and
the date and time of the test.
Your glucose test result will flash on the display
to indicate that it is being transmitted to your
partner device. The result will stop flashing after
it has been received. After about 60 seconds, if
the result has not been received by the partner
device, the transmit feature will turn off and the
result will stop flashing.
to indicate that it is being transmitted to your
partner device. The result will stop flashing after
it has been received. After about 60 seconds, if
the result has not been received by the partner
device, the transmit feature will turn off and the
result will stop flashing.
If the test results are lower than, higher than,
or not what you expect, see pages 34–36.
or not what you expect, see pages 34–36.
iii
Setting up
pg.
2
your system
Table of contents
• Getting to know your
OneTouch
®
UltraLink
™
Blood
Glucose Meter and Test Strips
• Turning your meter on and off
• Setting up your meter
• Turning the PUMP COMM
(partner device communication)
feature on and off.
feature on and off.
Your meter comes pre-set to
automatically transmit glucose
test results to your partner
device. You will also need to
program your meter ID into
your partner device for results
to be transmitted. See page 10
for instructions on where to
find your meter ID and how to
program it into your partner
device.
automatically transmit glucose
test results to your partner
device. You will also need to
program your meter ID into
your partner device for results
to be transmitted. See page 10
for instructions on where to
find your meter ID and how to
program it into your partner
device.
Starting the test process
pg.
12
NOTE: Before testing, read
this owner’s booklet carefully.
this owner’s booklet carefully.
Insert a test strip
Check the code on the test strip
vial before inserting the test
strip. Make sure the three
contact bars are facing you.
Push the test strip in as far as
it will go.
Check the code on the test strip
vial before inserting the test
strip. Make sure the three
contact bars are facing you.
Push the test strip in as far as
it will go.
Do Not bend the test
strip.
The meter will turn on, show a
black start-up screen and then a
code number. The first time you
use the meter, the
black start-up screen and then a
code number. The first time you
use the meter, the
CAL CODE
screen will display “––” instead
of a number.
of a number.
Match the code displayed on
the meter with the code on the
test strip vial
If the code on the meter does
not match the code on the vial,
press
the meter with the code on the
test strip vial
If the code on the meter does
not match the code on the vial,
press
or
to change the
code. If the display changes to
the
the
APPLY BLOOD
screen before
you are ready, remove the
teststrip and re-start the test
process.
teststrip and re-start the test
process.
Press
when the numbers
match.
The meter is ready for testing
when the
when the
APPLY BLOOD
screen
appears.
OK
ii