Справочник Пользователя для ZyXEL Communications Corporation VMG1312T10C
Chapter 5 WAN Setup
VMG1312-T10C User’s Guide
40
The following table describes the labels in this screen.
Table 3
Network Setting > Broadband >Internet Connection
LABEL
DESCRIPTION
Line
DSL Mode
Select the kind of connection your Device uses to connect to the ISP.
Use Auto Sync-Up if you are not sure which type to choose.
Use VDSL2, ADSLT1.413, ADSLG.DMT, ADSLG.lite, ADSL2, ADSL2+,
ADSL2_AnnexM, ADSL2+_AnnexM, or READSL2 if you know the specific type of
DSL the Device uses to connect to the ISP.
ADSL2_AnnexM, ADSL2+_AnnexM, or READSL2 if you know the specific type of
DSL the Device uses to connect to the ISP.
Type
Select the kind of connection your Device uses to connect to the ISP.
Use Auto Sync-Up if you are not sure which type to choose.
Use VDSL, ADSL2+, ADSL2, G.DMT, T1.413 or G.lite if you know the specific type
of DSL the Device uses to connect to the ISP.
of DSL the Device uses to connect to the ISP.
Use Ethernet if you use an Ethernet port Device to connect to the ISP.
Note:
Changing the line type between DSL and Ethernet causes the Device to restart.
Virtual Channel
When you set DSL Mode to Auto Sync-Up, select whether to configure the ADSL
virtual circuit or the first VDSL virtual circuit.
virtual circuit or the first VDSL virtual circuit.
When you set DSL Mode to ADSL or VDSL, this uses the virtual circuit of that type.
Mode
Select Router (default) from the drop-down list box if your ISP gives you one IP
address only and you want multiple computers to share an Internet account. Select
Bridge when your ISP provides you more than one IP address and you want the
connected computers to get individual IP address from ISP’s DHCP server directly. If
you select Bridge, you cannot use Firewall, DHCP server and NAT on the Device.
address only and you want multiple computers to share an Internet account. Select
Bridge when your ISP provides you more than one IP address and you want the
connected computers to get individual IP address from ISP’s DHCP server directly. If
you select Bridge, you cannot use Firewall, DHCP server and NAT on the Device.
Encapsulation
Select the method of encapsulation used by your ISP from the drop-down list box.
Choices vary depending on the mode you select in the Mode field.
Choices vary depending on the mode you select in the Mode field.
If you select Router in the Mode field, select ENET ENCAP, IPoA, PPPoE, or
PPPoA. IPoA and PPPoA are not available for VDSL virtual channel.
PPPoA. IPoA and PPPoA are not available for VDSL virtual channel.
If you select Bridge in the Mode field, you do not configure the method of
encapsulation.
encapsulation.
User Name
(PPPoA and PPPoE encapsulation only) Enter the user name exactly as your ISP
assigned. If assigned a name in the form user@domain where domain identifies a
service name, then enter both components exactly as given.
assigned. If assigned a name in the form user@domain where domain identifies a
service name, then enter both components exactly as given.
Password
(PPPoA and PPPoE encapsulation only) Enter the password associated with the user
name above.
name above.
Service Name
(PPPoE only) Type the name of your PPPoE service here.
Multiplex
This displays for an ADSL virtual channel. Select the method of multiplexing used by
your ISP from the drop-down list. Choices are VC-Mux or LLC.
your ISP from the drop-down list. Choices are VC-Mux or LLC.
IPv6/IPv4 Dual Stack
This is not available if you select PPPoA in the Encapsulation field.
Select IPv4 to have the Device use only IPv4.
Select IPv4/IPv6 to let the Device connect to IPv4 and IPv6 networks and choose
the protocol for applications according to the address type.
the protocol for applications according to the address type.
Select IPv6 to have the Device use only IPv6.