Справочник Пользователя для HID Global Corporation 6055BC

 

 
 

 

 

_________________________________________________________________________________________________ 
HID Corporation  9292 Jeronimo Road  Irvine, CA 92618-1905 USA   TEL (949)598-1600  (800)237-7769  
FAX (949)598-1690     Internet - www.hidcorp.com - HID Mifare Reader Installation Manual 6055-914 Rev A.0          Page 2 of 4 

 

- HID MIFARE Reader with snap-on 
cover and 18in.  

1 

- #6-32 x 1” self-tapping panhead 
screw 

2 

- Installation manual 

1 

 

- Wire splice 

9 

- DC Power supply 12 VDC 

1 

 

•  Determine an appropriate mounting location. The 

reader may be mounted to any surface, including 
metal. 

• 

Drill two (2) 3/32-inch (2.5mm) holes 

approximately 1 inch deep for mounting the 
reader. 

•  Drill a 5/8-inch (16mm) hole for the cable. 
•  A single-gang (2S) electrical junction box may 

also be used; reader fits US hole pattern, and the 
6-32 screws work with the J-box. 

•  Remove the snap-on cover from the reader and 

secure the reader to the mounting surface. 

•  Route the cable from the reader and/or power 

supply to the host. A linear type power supply is 
recommended. Check all electrical codes for 
proper cable installation. 

•  For the cable connection to the panel - use Alpha 

#1299C or equivalent.  

•  Test the operation of the reader (Section 4). After 

completion of the test, replace the snap-on cover. 

• See Figure 1 for product and mounting 

dimensions. 

•  For proper regulatory compliance, the drain wire 

should be disconnected at the power supply end 
of the cable. 

•  Changes or modifications not expressly approved 

by the party responsible for compliance could 
void the user’s authority to operate the 
equipment. 

•  The Reader is intended to be powered from a 

limited power source output of a previously 
certified power supply. 

•  Connect the reader to the host according to the 

wiring table below and the host installation guide. 

9-14 VDC 

Red 

   - 

   - 

GND 

Black 

Pin 5 

Pin 7 

D0 

Green 

   - 

   - 

D1 

White 

   - 

   - 

GRN LED 

Orange 

   - 

   - 

RED LED 

Brown 

   - 

   - 

Beeper 
HOLD 
DSR 
RX 
DTR 
TX 
SHLD GND 

Yellow 
Blue 
Violet 
Pink 
Gray 
Tan 
Drain 

   - 
Pin 1 
- 
Pin 2 
Pin 4 
Pin 3 
   - 

   - 
Pin 8 
- 
Pin 3 
Pin 20 
Pin 2 
   - 

 

•  When power is applied to the reader the beeper 

will beep and flash the LED green three times.  

•  Present an ID card to the reader. The LED will 

momentarily turn green while the beeper beeps 
once, indicating that the card was read 
successfully. 

•  Please note that typical read range for MIFARE® 

cards is .75 to 1.5” (20 – 37 mm). 

 
 
 

Power supply  

Absolute Maximum Voltage  

Maximum Current at 12V             

Operating Voltage Range             

Linear type 

16 VDC 

94mA 

9.0 – 14.0 VDC 

Maximum cable distance             
To host                                          

50 ft RS-232 

500 ft Wiegand 

Operating temperature range       

-30 to 65

°C           

FCC Compliance Statement: This device complies 
with part 15 of the FCC rules. Operation is subject to 
the following two conditions: (1) this device may not 
cause harmful interference, and (2) this device must 
accept any interference received, including 
interference that may cause undesired operation.