Справочник Пользователя для KAPSCH TRAFFICCOM CANADA INC. 801800A

If securing the transponder WITH the mounting plate:

1. The back of the mounting plate is covered with 3M™ VHB™ acrylic

foam tape. Prepare the mounting location in accordance with 3M™
document 70-0704-8701-5.

NOTE: Ensure the mounting plate is installed on the vehicle so that when

the transponder is installed on the mounting plate, the orientation
arrows on the transponder point in the direction of forward travel.

2. Remove the protective backing from the adhesive on the back of the

mounting plate and firmly press the mounting plate against the
mounting surface with either a roller or platen pressure, maintaining
pressure for 15 seconds to ensure a good bond.

3. Using the supplied tamper-proof nuts, lock washers, and flat washers,

secure the transponder to the mounting plate with the notches on the
transponder and mounting plate aligned and with the orientation
arrows on the transponder pointing in the direction of forward travel.

©Ka

icC

IVH

rig

ect

lte

tio

ith

tice

Kapsch Group
The Kapsch Group and its entities Kapsch TrafficCom, Kapsch CarrierCom and Kapsch BusinessCom are specialized in the future-oriented market
segments of Intelligent Transportation Systems (ITS) and Information and Communication Technologies (ICT). Kapsch. Always one step ahead.

801850

-0

If securing the transponder WITHOUT the mounting plate:

NOTE: The transponder mounting holes must be used when securing the

transponder to the roof of the vehicle using this method.

1. Place the transponder in the selected mounting location. Using the

transponder mounting holes as a guide, mark the locations on the roof
through which the mounting bolts will pass. Remove the transponder.

2. Drill a mounting bolt hole at both locations marked in step 1.

3. Using two, ¼- in.-diameter stainless steel mounting bolts of sufficient

length, two tamper-proof nuts, two lock washers, and two stainless
steel flat washers, secure the transponder to the roof of the vehicle
with the orientation arrows on the transponder pointing in the direction
of forward travel.

4. Apply sealant to the mounting bolts and mounting location as

necessary.

transponder

tamper-proof nut

flat washer

mounting bolt

Alternate FME location: front of vehicle

Select a mounting location either on the front license plate using the

license plate mounting screws or on the front of the vehicle using the

mounting plate. Consider the following criteria:

A: a minimum of 24 in. clearance if bumper or large object extends 7+

in. (A

B: a minimum of 15 in. from the top of the transponder to the roadway

for front bumper mounting.

C: the transponder must be mounted within 4 in. of the vehicle center.

If mounting the transponder on the front license plate:

1. Remove the two upper license plate mounting screws securing the

license plate to the front of the vehicle.

2. Using the license plate mounting screws removed in step 1, secure

the transponder, with orientation arrows pointing skyward, and the
license plate to the front of the vehicle.

If mounting the transponder elsewhere on the front of the vehicle:

1. The back of the mounting plate is covered with 3M™ VHB™ acrylic

foam tape. Prepare the mounting location in accordance with 3M™
document 70-0704-8701-5.

NOTE: Ensure the mounting plate is installed on the vehicle so that when

the transponder is installed on the mounting plate, the orientation
arrows on the transponder point in the direction of forward travel.

2. Remove the protective paper from the adhesive on the back of the

mounting plate and firmly press the mounting plate against the
mounting surface with either a roller or platen pressure, maintaining
pressure for 15 seconds to ensure a good bond.

3. Using the supplied tamper-proof nuts, lock washers, and flat washers,

secure the transponder to the mounting plate with the notches on the
transponder and mounting plate aligned and with the orientation
arrows on the transponder pointing skyward.

tamper-proof nut

lock washer
flat washer

transponder

notch

mounting plate

mounting plate stud

orientation arrow

lock washer