Справочник Пользователя для EMS Technologies Canada Ltd. HSD-X
Page 3–44
18 September 2007
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
C. Section III: Cooperative Mode Installation
(1) Cooperative Mode Installations Wiring Notes
This section provides detailed information on the external interface and system
connections involved in the installation of an HSD transceiver in Cooperative Mode
operation.
connections involved in the installation of an HSD transceiver in Cooperative Mode
operation.
(a) General Overview – Cooperative Mode
This section describes external interfaces unique to HSD Transceivers operating
in Collins SAT-906 Cooperative-Mode. For detailed interface descriptions, refer
to the Cooperative Mode, Interconnection Diagram, (1110-B-0156).
in Collins SAT-906 Cooperative-Mode. For detailed interface descriptions, refer
to the Cooperative Mode, Interconnection Diagram, (1110-B-0156).
Note:
All connections, except power and RF, are HSD specific. Refer to “other
SATCOM” and antenna manufacturers’ installation documentation for
interconnection wiring details.
SATCOM” and antenna manufacturers’ installation documentation for
interconnection wiring details.
To achieve the current “best system” operation performance, the HSD should
have EMS SATCOM service bulletin 1110-SB-0015 incorporated (service bulletin
1110-SB-0015 supercedes 1110-SB-0003). Cooperative Mode installations that
use an HSD without a minimum of service bulletin 1110-SB-0003 (control
processor software version 4.5) incorporated will occasionally generate Disable
0100, Disable 0800, and Disable 1000 SAT-906 system errors.
have EMS SATCOM service bulletin 1110-SB-0015 incorporated (service bulletin
1110-SB-0015 supercedes 1110-SB-0003). Cooperative Mode installations that
use an HSD without a minimum of service bulletin 1110-SB-0003 (control
processor software version 4.5) incorporated will occasionally generate Disable
0100, Disable 0800, and Disable 1000 SAT-906 system errors.
Cooperative Mode system installations that use an HSD with service bulletin
1110-SB-0003 incorporated operate with improved system performance and
should only generate Disable 1000 SAT-906 system errors (Disable 1000 errors
occur on approximately 1% of M4 call terminations). This error occurs due to the
HSD reporting a lower than expected actual power out value in the HPA Status
Word on the ARINC 429 HPA BITE bus.
1110-SB-0003 incorporated operate with improved system performance and
should only generate Disable 1000 SAT-906 system errors (Disable 1000 errors
occur on approximately 1% of M4 call terminations). This error occurs due to the
HSD reporting a lower than expected actual power out value in the HPA Status
Word on the ARINC 429 HPA BITE bus.
Currently, Cooperative Mode installations only support single channel card
configurations. If installing a dual-channel HSD transceiver in a Cooperative
Mode environment, use the maintenance port utility to configure the EEPROM
setting, in Menu 3, for a single channel card.
configurations. If installing a dual-channel HSD transceiver in a Cooperative
Mode environment, use the maintenance port utility to configure the EEPROM
setting, in Menu 3, for a single channel card.
The following general wiring notes must be considered before installing an HSD
transceiver for Cooperative Mode operation with the Collins SAT-906 system.
transceiver for Cooperative Mode operation with the Collins SAT-906 system.
•
Splitter for the RX path
•
System Configuration strapping is set to “Cooperative Rockwell-Collins
SAT-906” in the EEPROM parameter for software versions 4.5. External
system strapping to “Collins Cooperative” Mode is used for installations
operating software versions 5.7 or later (1110-SB-0011). Software versions
5.7 or later “read” the hardware strapping to automatically identify the system
configuration.
SAT-906” in the EEPROM parameter for software versions 4.5. External
system strapping to “Collins Cooperative” Mode is used for installations
operating software versions 5.7 or later (1110-SB-0011). Software versions
5.7 or later “read” the hardware strapping to automatically identify the system
configuration.
Add the following HSD-specific wiring:
•
Forward ID Address (Category B)
•
Antenna to BSU BITE information from SDU
•
A “Tx Disable” line from the SDU to the HSD
•
ARINC 429 SDU to/from HSD, Crosstalk BUS lines
Other HSD-specific wiring includes: