Справочник Пользователя для VTech Telecommunications Ltd 80-1254-00

Below are the questions most frequently asked about

the baby monitor. If you cannot find the answer to your
question, visit our website at

www.vtechphones.com,

or contact

1 (800) 595-9511 for customer service.

Why doesn’t

the

POWER

light on the

baby unit turn

on when I

switch on the

units?

Perhaps the baby unit is not

connected to the power supply.
Connect the baby unit to power

supply. The baby unit turns on.

Why doesn’t

the

/ LINK light

on the parent

unit turn on

when I switch

on the units?

Perhaps the battery of the parent

unit is empty and the parent unit is

not connected to power supply.

Connect the parent unit to power

supply; or insert two new AAA

alkaline batteries into the parent

unit. The parent unit turns on and

establishes connection with the

baby unit.

Why does the

baby monitor

not respond

normally?

Try the following (in the order 

listed) for common cure:
1. Make sure that both baby 

unit and parent unit are on. 

Disconnect the power from the 

baby unit and the parent unit.

2. Remove the batteries from the 

parent unit.

3. Connect the baby unit to the 

power supply again. The baby unit 

turns on.

4. Connect the parent unit to the 

power supply again; or insert 

two new AAA alkaline batteries. 

The parent unit turns on.

5. Wait for the parent unit to 

synchronize with the baby unit. 

Allow up to one minute for this 

to take place.

6. Press 

or   to adjust the 

speaker volume on the parent 

unit.

Why does the

baby monitor

produce a

high-pitched

noise?

The units may be too close to

each other. Make sure the parent

unit and the baby unit at least

6.5 feet / 2 meters away from each

other.

Why don’t I

hear a sound/

Why can’t I

hear my baby

cry?

Make sure that both baby unit and

parent unit are on. If you see the

visual sound indicators light up,

but there is no sound, then you

may have muted the volume or

set it to a lower level. Adjust the

volume to a higher level.

If the visual sound indicators do

not light up, and you cannot hear

any sound, it is because the baby

sound is too low for the baby unit

to detect. This is normal. Place

the baby unit at least 6.5 feet / 2

meters away from your baby.

Why does the

parent unit

beep?

The parent unit beeps three times

every 30 seconds when the baby

unit is out of range. Move the

parent unit closer to the baby

unit (but not less than 6.5 feet / 2

meters).

If the parent unit is powered by

batteries, the parent unit beeps

twice every 10 minutes and the

 light flashes in red when the

battery is low. Replace with two

new AAA alkaline batteries.

Why does

the parent

unit

 light

flash?

If the parent unit is powered by

batteries, the parent unit beeps

twice every 10 minutes and the

 light flashes in red when the

battery is low. Replace with two

new AAA alkaline batteries, or

remove the batteries, and connect

the parent unit to the power supply.

Why can’t I

establish a

connection?

Why is the

connection

lost every

now and

then? Why

are there

sound

interruptions?

The baby unit may be out of range.

Move the parent unit closer to the

baby unit (but not less than

6.5 feet / 2 meters).

Other electronic products may

cause interference with your baby

monitor. Try installing your baby

monitor as far away from these

electronic devices as possible.

When using your equipment, basic safety

precautions should always be followed to

reduce the risk of fire, electric shock and

injury, including the following:

1.  Follow all warnings and instructions marked on

the product.

2.  Adult setup is required.
3.  This product is intended as an aid. It is not

a substitute for responsible and proper adult

supervision and should not be used as such.

4.  This product is not intended for use as a medical

monitor.

5.  Do not use this product near water. For example,

do not use it next to a bath tub, wash bowl,

kitchen sink, laundry tub or swimming pool, or in

a wet basement or shower.

6.

CAUTION: Use only alkaline batteries (not

included). There may be a risk of explosion if a

wrong type of battery is used for the parent unit.

Do not dispose of batteries in a fire. They may

explode. Check with local codes for possible

special disposal instructions.

7.  Use only the adapters included with this product.

Incorrect adapter polarity or voltage can

seriously damage the product.

Baby unit power adapter: Input: 100-120V AC 60

Hz; output: 6V DC 400 mA

Parent unit power adapter: Input: 100-120V AC 60

Hz Output: 6V DC 400mA.

8.  The power adapters are intended to be correctly

oriented in a vertical or floor mount position. The

prongs are not designed to hold the plug in place

if it is plugged into a ceiling, under-the-table or

cabinet outlet.

9.  For pluggable equipment, the socket-outlet

shall be installed near the equipment and shall

be easily accessible.

10.  Unplug this product from the wall outlet before

cleaning. Do not use liquid or aerosol cleaners.

Use a damp cloth for cleaning.

11.  Unplug the power cords before replacing batteries.
12.  Do not cut off the power adapters to replace

them with other plugs, as this causes a

hazardous situation.

13.  Do not allow anything to rest on the power cords.

Do not install this product where the cords may

be walked on or crimped.

14.  This product should be operated only from the

type of power source indicated on the marking

label. If you are not sure of the type of power

supply in your home, consult your dealer or local

power company.

15.  Do not overload wall outlets or use an extension

cord.

16.  Do not place this product on an unstable table,

shelf, stand or other unstable surfaces.

17.  This product should not be placed in any area

where proper ventilation is not provided. Slots

and openings in the back or bottom of this

product are provided for ventilation. To protect

them from overheating, these openings must

not be blocked by placing the product on a soft

surface such as a bed, sofa or rug. This product

should never be placed near or over a radiator or

heat register.

18.  Never push objects of any kind into this product

through the slots because they may touch

dangerous voltage points or create a short circuit.

Never spill liquid of any kind on the product.

19.  To reduce the risk of electric shock, do not

disassemble this product, but take it to an

authorized service facility. Opening or removing

parts of the product other than specified

access doors may expose you to dangerous

voltages or other risks. Incorrect reassembling

can cause electric shock when the product is

subsequently used.

20. You should test the sound reception every

time you turn on the units or move one of the

components.

21.  Periodically examine all components for

damage.

22. Be aware of possible loss of privacy while using

public airwaves. Conversations may be picked

up by other nursery monitors, cordless phones,

scanners, etc.

23. Children should be supervised to ensure that

they do not play with the product.

24.  The product is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or lack of

experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety.

Cautions
1.  Use and store the product at a temperature

between 32

o

F and 104

o

F.

2.  Do not expose the product to extreme cold, heat

or direct sunlight. Do not put the product close to

a heating source.

3.  Batteries should not be exposed to excessive

heat such as bright sunshine or fire.

4.

Make sure the baby unit and the adapter cord

are always out of reach of the baby, at least 3

feet (1 meter) away from the baby or crib, to

avoid a possible strangulation hazard.

5.  Never place the baby unit(s) inside the baby’s crib

or playpen. Never cover the baby unit(s) or parent

unit with anything such as a towel or a blanket.

6.  Never cover the baby unit or parent unit(s) with

anything such as a towel or a blanket.

7.  Other electronic products may cause

interference with your baby monitor. Try

installing your baby monitor as far away from

these electronic devices as possible: wireless

routers, radios, cellular telephones, intercoms,

room monitors, televisions, personal computers,

kitchen appliances and cordless telephones.

Cardiac pacemakers (applies only to digital cordless

devices):
Wireless Technology Research, LLC (WTR), an

independent research entity, led a multidisciplinary

evaluation of the interference between portable

wireless devices and implanted cardiac

pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:

Pacemaker patients
•  Should keep wireless devices at least six inches

from the pacemaker.

•  Should NOT place wireless devices directly over

the pacemaker, such as in a breast pocket, when

it is turned ON.

WTR’s evaluation did not identify any risk to

bystanders with pacemakers from other persons

using wireless devices.

Electromagnetic fields (EMF)
This VTech product complies with all standards

regarding electromagnetic fields (EMF). If handled

properly and according to the instructions in this

user’s manual, the product is safe to be used based

on scientific evidence available today.

FCC Part 15
This equipment has been tested and found to

comply with the requirements for a Class B digital

device under Part 15 of the Federal Communications

Commission (FCC) rules. These requirements are

intended to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However,

there is no guarantee that interference will not occur

in a particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to

try to correct the interference by one or more of the

following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment

and receiver.

•

Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

•

Consult the dealer or an experienced radio/TV

technician for help.

WARNING: Changes or modifications to this

equipment not expressly approved by the party

responsible for compliance could void the user’s

authority to operate the equipment.
This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.
To ensure safety of users, the FCC has established

criteria for the amount of radio frequency energy

that can be safely absorbed by a user or bystander

according to the intended usage of the product. This

product has been tested and found to comply with

the FCC criteria. The baby unit shall be installed

and used such that parts of all persons’ body are

maintained at a distance of approximately 8 in (20

cm) or more.
This Class B digital apparatus complies with

Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada  

licence-exempt RSS standard(s).
Operation is subject to the following two conditions:  

(1) this device may not cause harmful interference 

received, and (2) this device must accept any 

interference received, including interference that may 

cause undesired operation.
The term ‘’IC:‘’ before the certification/registration 

number only signifies that the Industry Canada 

technical specifications were met.
This product meets the applicable Innovation, 

Science and Economic Development Canada 

technical specifications.

The baby unit complies with FCC RF radiation 

exposure limits set forth for an uncontrolled 

environment. The baby unit should be installed 

and operated with a minimum distance of 20 cm 

(8 inches) between the baby unit

 

and all persons’ 

body. For body worn operation, this parent unit 

has been tested and meets the FCC RF exposure 

guidelines. Use of other accessories may not ensure 

compliance with FCC RF exposure guidelines. This 

transmitter must not be co-located or operating in 

conjunction with any other antenna or transmitter. 

This equipment complies also with Industry Canada 

RSS-102 with respect to Canada’s Health Code 6 for 

Exposure of Humans to RF Fields.

Lorsque vous utilisez votre appareil, vous devriez 

toujours suivre certaines mesures de précaution 

de base afin de réduire les risques d’incendie, 

d’électrocution et de blessures corporelles, dont 

ceux qui suivent :
1.  Observez toutes les instructions et mises en 

garde inscrites sur l’appareil.

2.  L’installation par un adulte est requise.
3.  Ce produit a été conçu pour être un dispositif 

d’appoint seulement. Il n’est pas le remplacement 

d’une supervision responsable et adéquate par un 

adulte et ne devrait pas être utilisé comme telle.

4.  Ce produit n’est pas conçu pour être utilisé en 

tant que moniteur médical.

5.  N’utilisez pas cet appareil près de l’eau ni de 

toute autre source d’humidité, par exemple, près 

d’une baignoire, cuve à lessive, évier de cuisine, 

dans un sous-sol humide ni près d’une piscine, 

dans un soussol humide ou une douche.

6.

MISE EN GARDE : Il peut y avoir un risque 

d’explosion si vous utilisez le mauvais type de 

bloc-piles pour l’unité du parent. N’incinérez pas 

les piles. Celles-ci risqueraient d’exploser.

7.  N’utilisez que les adaptateurs inclus avec ce 

produit. L’utilisation d’un adaptateur dont la 

polarité ou la tension serait inadéquate risque 

d’endommager sérieusement le produit et mettre 

votre sécurité en péril. 

Adaptateur de l’unité du bébé : 

 

Entrée 100-120V AC 60 Hz; Sortie : 6V DC  

400 mA 

Adaptateur de l’unité du parent : 

Entrée 100-120V AC 60 Hz; Sortie : 6V DC  

400 mA

8.  Lorsqu’ils sont branchés dans une prise de 

courant, les adaptateurs secteur ont été conçus 

pour être orientés correctement, soit à la 

verticale ou au plancher. Les broches n’ont pas 

été conçues pour supporter le poids du bloc 

d’alimentation et le maintenir en place si celuici 

est branché dans une prise au plafond, sous une 

table ou dans un meuble.

9.  Pour les PRODUITS À BRANCHER À UNE 

PRISE DE COURANT, la prise de courant doit 

être installée près du produit, afin d’assurer une 

accessibilité sécuritaire à la prise de courant.

10.  Débranchez ce produit de la prise de courant 

avant de procéder au nettoyage. N’utilisez pas de 

nettoyants en aérosols. Utilisez un chiffon humide 

pour le nettoyer.

11.  Débranchez les cordons d’alimentation avant de 

remplacer le bloc-piles.

12.  Ne coupez pas les cordons d’alimentation pour 

remplacer les fiches, car ceci peut présenter un 

danger potentiel.

13.  Ne laissez aucun objet reposer ni appuyer sur 

le cordon d’alimentation. N’installez pas cet 

appareil dans un endroit où l’on risque d’écraser 

le cordon d’alimentation ou de le piétiner.

14.  Ne faites fonctionner cet appareil qu’avec le 

type d’alimentation indiqué sur l’étiquette. Si 

vous ne connaissez pas le type d’alimentation 

que vous possédez à votre domicile, consultez 

votre marchand ou votre compagnie locale 

d’électricité.

15.  Ne surchargez pas les prises de courant 

murales ni les rallonges électriques.

16.  Ne placez pas cet appareil sur un chariot, 

meuble, trépied, support de montage ni table 

chancelants.

17.  Les trous et ouvertures du boîtier, situés à 

l’arrière de l’appareil ou sous celui-ci, servent à 

aérer l’appareil. Pour l’empêcher de surchauffer, 

ne bloquez sous aucun prétexte ces ouvertures 

et n’empêchez pas l’aération adéquate de 

l’appareil en le plaçant sur un lit, divan, tapis ou 

toute autre surface similaire. De même, ne le 

positionnez pas à proximité ni au-dessus d’une 

source de chaleur ou d’un calorifère. De plus, ne 

placez pas l’appareil dans un endroit avant de 

vous assurer qu’il y ait une bonne circulation d’air.

18.  N’enfoncez jamais d’objets à travers les 

ouvertures de cet appareil, car ils pourraient 

entrer en contact avec des points de tension 

dangereux ou causer des courts-circuits qui 

peuvent dégénérer en incendies ou en risques 

d’électrocution. Ne renversez jamais de liquide 

dans ce produit.

19.  Afin de réduire les risques d’électrocution, ne 

démontez pas cet appareil, mais apportez-le 

dans un centre de service autorisé. L’ouverture 

du boîtier ou le retrait de toutes pièces que 

contient cet appareil, à l’exception de l’accès 

autorisé à certaines portes ou ouvertures, 

risque de vous exposer à des points de tension 

dangereux ou d’autres dangers. Un remontage 

incorrect peut par la suite présenter des risques 

d’électrocution.

20.  Vous devriez tester la réception chaque fois que 

vous mettez l’appareil en fonction.

21.  Examinez les composantes afin de vérifier si 

celles-ci ne sont pas endommagées.

22.  Soyez avisé de la perte de la confidentialité 

lorsque vous utilisez les ondes publiques. Les 

conversations peuvent être entendues par 

d’autres moniteurs de bébé, des téléphones 

sans fil, des scanneurs, etc.

23.  Les enfants devraient être supervisés afin de 

vous assurer qu’ils ne jouent pas avec l’appareil.

24.  Le produit n’est pas conçu pour être utilisé 

par des personnes (incluant des enfants) aux 

capacités physiques, sensorielles ou mentales 

réduites ou qui manquent d’expérience et de 

connaissances, à moins qu’on leur ait donné 

suffisamment de supervision ou d’instructions 

relativement à l’utilisation de l’appareil par une 

personne responsable de leur sécurité.

1.  Utilisez et entreposez le produit à une 

température entre 0˚ C (32˚F) et 40˚C (104˚ F).

2.  N’exposez pas cet appareil à des froids ou des 

chaleurs extrêmes, ainsi qu’à la lumière directe 

du soleil. Ne l’installez pas près d’une source de 

chauffage.

3.  Le bloc-piles ne doit pas être exposé à la chaleur 

excessive telle que la lumière du soleil ou au feu.

4.  Assurez-vous que le moniteur et le cordon 

de l’adaptateur sont toujours hors de portée 

des enfants, à au moins 1 mètre (3 pieds) de 

l’enfant ou du berceau, pour éviter tout risque de 

strangulation.

5.  Ne jamais placer le moniteur à l’intérieur du 

berceau ou du parc de bébé. Ne jamais couvrir 

le moniteur ou l’unité (s) portative avec un article 

tel une serviette ou une couverture.

6.  D’autres équipements électroniques peuvent 

produire des interférences sur votre moniteur 

vidéo et audio. Tentez d’installer votre 

moniteur vidéo ou audio à l’écart des appareils 

électroniques tels que des routeurs sans fil, 

radios, téléphones cellulaires, interphones, 

moniteurs, téléphones, ordinateurs personnels, 

électroménagers et téléphones sans fil.

Les simulateurs cardiaques (ne s’applique qu’aux 

dispositifs numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC 

(WTR)’, une firme de recherche indépendante, 

a mené une évaluation pluridisciplinaire des 

interférences entre les téléphones sans fil portatifs 

et les stimulateurs cardiaques implantés dans 

l’organisme. Appuyée par l’Administration des 

aliments et drogues (FDA) des États-Unis, la firme 

WTR recommande aux médecins:

•  Vous devriez maintenir les dispositifs sans fil à au 

moins six pouces du simulateur cardiaque.

•  Ils ne doivent PAS placer le téléphone sans fil 

directement sur le stimulateur cardiaque, tel que 

dans une poche de chemise, lorsque celui-ci est 

en marche.

L’étude effectuée par l’organisme WRS n’a pas 

identifié de risque pour les détenteurs de simulateurs 

cardiaques causés par les gens qui utilisent 

dispositifs sans fil à proximité de ceux-ci.

Ce produit de VTech est conforme à toutes 

les normes se rapportant aux champs 

électromagnétiques (EMF) standard. Si vous le 

manipulez correctement en suivant les instructions 

de ce guide, son utilisation sera sécuritaire pendant 

de nombreuses années, selon les meilleures 

évidences scientifiques dont nous disposons 

aujourd’hui.

aujourd’hui.

What does this limited warranty cover?
The manufacturer of this VTech Product warrants to

the holder of a valid proof of purchase (“Consumer”

or “you”) that the Product and all accessories

provided in the sales package (“Product”) are

free from defects in material and workmanship,

pursuant to the following terms and conditions,

when installed and used normally and in accordance

with the Product operating instructions. This limited

warranty extends only to the Consumer for Products

purchased and used in the United States of America

and Canada.

Product”)?
During the limited warranty period, VTech’s

authorized service representative will repair

or replace at VTech’s option, without charge,

a Materially Defective Product. If we repair

the Product, we may use new or refurbished

replacement parts. If we choose to replace the

Product, we may replace it with a new or refurbished

Product of the same or similar design. We will

retain defective parts, modules, or equipment.

Repair or replacement of the Product, at VTech’s

option, is your exclusive remedy. VTech will return

the repaired or replacement Products to you in

working condition. You should expect the repair or

replacement to take approximately 30 days.

How long is the limited warranty period?
The limited warranty period for the Product extends

for ONE (1) YEAR from the date of purchase. If

VTech repairs or replaces a Materially Defective

Product under the terms of this limited warranty,

this limited warranty also applies to the repaired

or replacement Product for a period of either (a)

90 days from the date the repaired or replacement

Product is shipped to you or (b) the time remaining

on the original one-year warranty; whichever is

longer.

What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse,

accident, shipping or other physical damage,

improper installation, abnormal operation or

handling, neglect, inundation, fire, water or other

liquid intrusion; or

2. Product that has been damaged due to repair,

alteration or modification by anyone other than an

authorized service representative of VTech; or

3. Product to the extent that the problem experienced

is caused by signal conditions, network reliability,

or cable or antenna systems; or

4. Product to the extent that the problem is caused

by use with non-VTech accessories; or

5. Product whose warranty/quality stickers, product

serial number plates or electronic serial numbers

have been removed, altered or rendered illegible;

or

6. Product purchased, used, serviced, or shipped for

repair from outside the United States of America

or Canada, or used for commercial or institutional

purposes (including but not limited to Products

used for rental purposes); or

7. Product returned without a valid proof of purchase

(see item 2 in the next column); or

8. Charges for installation or set up, adjustment of

customer controls, and installation or repair of

systems outside the unit.

How do you get warranty service?
To obtain warranty service in the USA, please visit

our website at www.vtechphones.com or

call 1 (800) 595-9511. In Canada, go to

www.vtechcanada.com or call 1 (800) 267-7377.
NOTE: Before calling for service, please review the

user’s manual - a check of the Product’s controls

and features may save you a service call.
Except as provided by applicable law, you assume

the risk of loss or damage during transit and

transportation and are responsible for delivery or

handling charges incurred in the transport of the

Product(s) to the service location. VTech will return

repaired or replaced Product under this limited

warranty. Transportation, delivery or handling

charges are prepaid. VTech assumes no risk for

damage or loss of the Product in transit. If the Product

failure is not covered by this limited warranty, or proof

of purchase does not meet the terms of this limited

warranty, VTech will notify you and will request that

you authorize the cost of repair prior to any further

repair activity. You must pay for the cost of repair and

return shipping costs for the repair of Products that

are not covered by this limited warranty.

1.

Return the entire original package and contents

including the Product to the VTech service

location along with a description of the malfunction

or difficulty; and

2.

Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model)

and the date of purchase or receipt; and

3. Provide your name, complete and correct mailing

address, and telephone number.

Other limitations
This warranty is the complete and exclusive

agreement between you and VTech. It supersedes

all other written or oral communications related to this

Product. VTech provides no other warranties for this

Product. The warranty exclusively describes all of

VTech’s responsibilities regarding the Product. There

are no other express warranties. No one is authorized

to make modifications to this limited warranty and you

should not rely on any such modification.
State/Provincial Law Rights: This warranty gives you

specific legal rights, and you may also have other

rights, which vary from state to state or province to

province.
Limitations: Implied warranties, including those of

fitness for a particular purpose and merchantability (an

unwritten warranty that the Product is fit for ordinary

use) are limited to one year from the date of purchase.

Some states/provinces do not allow limitations on

how long an implied warranty lasts, so the above

limitation may not apply to you. In no event shall

VTech be liable for any indirect, special, incidental,

consequential, or similar damages (including, but

not limited to lost profits or revenue, inability to use

the Product or other associated equipment, the cost

of substitute equipment, and claims by third parties)

resulting from the use of this Product. Some states/

provinces do not allow the exclusion or limitation of

incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

Frequency

control

Crystal controlled PLL synthesizer

Transmit

frequency

Baby unit: 1921.536 - 1928.448 MHz

Parent unit: 1921.536 - 1928.448 MHz

Channels

5

Nominal

effective

range

Maximum power allowed by FCC

and IC. Actual operating range may

vary according to environmental

conditions at the time of use.

Power

requirements

Baby unit adapter:

Input: 100-120V AC 60Hz

Output: 6V DC @ 400mA
Parent unit adapter:

Input: 100-120V AC 60Hz

Output: 6V DC @ 400mA
Parent unit battery:

2 X AAA alkaline batteries

Specifications are subject to change without notice.
© 2018 VTech Communications, Inc.
All rights reserved. 02/18. DM1111-X_CIB_V2.0
Document order number: 91-010894-020-100