Справочник Пользователя для Climax Technology Co Ltd KPF1

                                                                                                                                                             

     

 

2

¾ Request 

for 

Home mode during Arm mode. 

¾ Request 

for 

Force arm. 

z 

z 

Flash: system failure (panel tamper, AC fault, sensor temper, sensor out of order, open door) 

z 

On: Alarm Memory (depend on Control Panel). 

z 

z 

Remote keypad uses one EL123AP 3V Lithium battery as its power source.   

z 

Remote keypad can also detect the battery status. If the battery voltage is low, the Active LED will flash (Amber in Test 
mode or Blue in Normal mode) during operation. The Low battery signal will be sent along with regular signal 
transmissions to the Control Panel for displaying the status accordingly. 

z 

Before shipment, the battery is pre-installed by the factory. Pull out the battery insulator to activate battery. 

z 

When changing battery, press the tamper switch a couple time after removing old battery to discharge, then insert the 
new battery. 

z 

z 

When idle, Remote keypad is in Stand-by mode and uses no power.    It will activate and wake-up for 5 seconds when 
any key is pressed. 

z 

After 5 seconds of key inactivity, the power goes off and it returns to Stand-by mode.   

z 

Upon completion of a command input, the power goes off and Remote keypad returns to Stand-by mode. 

z 

z 

Remote keypad can be put into Test mode by entering the Keypad PIN code (default: 0000) followed by  ＊  key.    The 
Active Amber LED will turn on along with a long beep. 

z 

To exit Test mode, press 

 key twice, Remote keypad will sound a long beep and the Active LED will turn off

, 

then 

Remote keypad returns to Normal Operation mode.    Otherwise, Remote keypad will automatically exit Test mode after 

5 minutes and return to Normal Operation mode. 

& 

The Test Mode is helpful for bypassing Remote keypad Tamper alarm when installing, replacing low batteries or 
removing to different mount site. 

& 

When Remote keypad is in Test mode, it operates as wake-up condition and will NOT disconnect after 5 seconds. 

„ Press 

＊ key and then 7 key — Transmit Remote keypad learn signal   

„ Press 

＊  key and then 2 key — Enable Dual-key Panic Alarm function   

„ Press 

＊ key and then 3 key — Enable Dual-key Fire Alarm function 

„ Press 

＊ key and then 4 key — Enable Dual-key Medical Alarm function 

„ Press 

＊ key and then 5 key — Disable all Dual Key function (Default) 

„ Press 

＊ key and then 6 key — Edit Keypad Pin Code   

Enter Old Keypad Pin Code and then press 

Χ key 

Enter New a new 4-digit Keypad Pin Code and then press # key. 

„ Press    key twice — to leave the Test Mode. 
„ Press 

＊ key and then 8 key — Enable Arm/ Home without PIN Code function 

„ Press 

＊ key and then 9 key — Enable Arm/ Home with Control Panel User PIN Code function (Default) 

z 

z 

The keypad is protected against any attempt to open the lid or to detach keypad from its mounting surface. 

z 

Tamper protection is disabled when the keypad is in Test Mode.     

z 

Step 1. 

Put the Control panel into learning mode, . 

Step 2. 

Adding remote keypad into the Control Panel: 

 

I. 

Put remote keypad in Test mode by entering KP PIN code (default: 0000), then press  ＊ key. The Active 
Amber LED will turn on along with a long beep sound. 

II. Press 

＊ key then 7 key. Remote keypad will sound a long beep.