Справочник Пользователя для Intermatic H0020

After including your HA20 In-Wall Dimmer with your Home-

Settings network, you must associate it with a specifi c control 

channel (or button) so you can operate it by remote control. 

For a non-HomeSettings network, follow controller instructions 

provided by the manufacturer. 

Decide which pair of 

 buttons you want to use to con-

trol the In-Wall Dimmer. Each pair represents a channel.
Press and hold (at the same time) both 

 and OFF buttons 

on the HA07 Master Controller or the HA09 Handy Controller. 

After about 3 seconds:

The Master Controller screen will display LEARN.

 -

The Handy Controller lights will rapidly fl ash GREEN and 

 -

RED at the same time.

Release the 

 and OFF buttons on the controller. 

Press and hold the 

 button on the Master Controller 

or the Handy Controller.

The Master Controller screen will display INCL.

 -

The Handy Controller will show a solid GREEN light only.

 -

While still holding the 

 button, adjust the TOGGLE 

switch on the In-Wall Dimmer to adjust the light to the de-

sired level. 
Release the 

 button. If the association is successful:

The Master Controller screen will display SUCCESSFUL.

 -

The Handy Controller GREEN light will simply turn off.

 -

Test the channel you have just programmed by pressing its 

 and OFF buttons. The light should power ON or OFF at the 

level you have set.
If the screen displays NOT SUCCESSFUL or the light is RED, 
the association has failed. Try again. If the procedure contin-
ues to fail, contact Intermatic Customer Service. 

3 – ASSOCIATE the In-Wall Dimmer with a Control Channel

If necessary, you can delete the HA20 In-Wall Dimmer from 

your HomeSettings network—or any network that supports 

Z-Wave devices—through a process called EXCLUSION. 

Put the controller into EXCLUSION mode. On the HA07 

Master Controller or the HA09 Handy Controller, press and 

release the DELETE button. For other manufacturers’ control-

lers, follow the instructions provided by the manufacturer.
Flip the 

 switch of the HA20 In-Wall Dimmer. If the 

exclusion is successful:

The HA07 screen will display SUCCESSFUL.

 -

The HA09 will show a solid GREEN light for 2 seconds.

 -

Optional: EXCLUDE the In-Wall Dimmer from your Network

After hard-wiring the HA20 into place, the device is ready to join 

your HomeSettings network—or any network that supports Z-

Wave™ devices—through a process called INCLUSION.  

Put the controller into INCLUSION mode. On the HA07 

Master Controller or the HA09 Handy Controller, press and 

release the INCLUDE button. For other 

manufacturers’ controllers, follow the 

instructions provided by the manu-

facturer.
Flip the 

 switch of the HA20 

In-Wall Dimmer. If the inclusion is 

successful:

The HA07 screen will display SUC-

 -

CESSFUL.
The HA09 will show a solid GREEN light for 2 seconds.

 -

2 – INCLUDE the In-Wall Dimmer in your Network

For control of permanently installed incandescent lamp 

• 

fi xtures only
Ratings: 600 Watts tungsten, 40 Watts minimum

• 

  

120 VAC, 50/60 Hz

Derating: 500 Watts double gang, 400 Watts triple gang

• 

Operating Temperature Range: 32°F to 104°F / 0°C to 40°C

• 

Radio Operating Frequency:  908.42 MHz @ 9.6 kbps

• 

  

 

 

         908.40 MHz @ 40 kbps

RF (wireless) Range: 100 ft. under operating conditions

• 

Made in China

•