Справочник Пользователя для Sony Corporation HCDDH7BT

CMT-DH7BT.GB.3-097-195-11(1)

CMT-

 Do not place the system in an inclined 

position or in locations that are extremely 
hot, cold, dusty, dirty, or humid or lacking 
adequate ventilation, or subject to vibration, 
direct sunlight or a bright light.

 Be careful when placing the unit or speakers 

on surfaces that have been specially treated 
(for example, with wax, oil, polish) as 
staining or discoloration of the surface may 
result.

 If the system is brought directly from a cold 

to a warm location or is placed in a very 
damp room, moisture may condense on the 
lens inside the DVD player, and cause the 
system to malfunction. In this situation, 
remove the disc, and leave the system turned 
on for about an hour until the moisture 
evaporates.

 Heat buildup on the unit during operation is 

normal and is not cause for alarm.

 Do not touch the cabinet if it has been used 

continuously at a high volume because the 
cabinet may have become hot.

 Do not obstruct the ventilation holes.

Th

  is speaker system is not magnetically 

shielded, and the picture on nearby TV 
sets may become magnetically distorted. In 
this situation, turn off  the TV, wait 15 to 30 
minutes, and turn it back on. If there is no 
improvement, move the speakers far away from 
the TV. 

Caution: If you leave a still video image 
or on-screen display image displayed on 
your TV for an extended period of time via 
this system, you risk permanent damage 
to your TV screen. Projection TVs are 
especially susceptible to this.

Clean this system with a soft  cloth slightly 
moistened with a mild detergent solution. 
Do not use any type of abrasive pad, scouring 
powder, or solvent, such as thinner, benzine, 
or alcohol. 

AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL 
HARMONIC DISTORTION:
With 6 ohm loads, both channels driven, 
from 120 – 10,000 Hz; rated 50 watts per 
channel minimum RMS power, with no 
more than 10% total harmonic distortion 
from 250 milliwatts to rated output.

DIN power output (rated)

40 W + 40 W (6 ohms at 1 kHz, DIN)

Continuous RMS power output (reference)
Front speaker:

50 W + 50 W (6 ohms at 1 kHz, 10% 
THD)

Inputs:
AUDIO IN (stereo mini jack):

Voltage 620 mV, impedance 
47 kilohms 

Outputs:
DIGITAL OUT (square optical connector 
jack):

Wavelength 660 nm

VIDEO OUT (phono jack):

Max. output level 1 Vp-p, unbalanced, 
Sync. negative load impedance 
75 ohms

COMPONENT VIDEO OUT:

Y: 1 Vp-p, 75 ohms
Pb/Cb: 0.7 Vp-p, 75 ohms
Pr/Cr: 0.7 Vp-p, 75 ohms

S VIDEO OUT (4-pin/mini-DIN jack):

Y: 1 Vp-p, unbalanced, Sync. negative
C: 0.286 Vp-p, load impedance 
75 ohms

PHONES (stereo mini jack):

accepts headphones of 8 ohms or 
more 

Comm

B

Outpu

B

Maxim

L

Freque

2
G

Modul

F

Compa

A
P
A
C

Suppor

R
T

1

2

System

C
v

Laser:
Laser D

E
L

*

Semico

(

Freque

D
(
C

Video 

N