Справочник Пользователя для INTERNATIONAL DEVELOPMENT COMPANY BT0445DS

IMPORTANT: Read all safety precautions and installations carefully before installing or 

servicing this fixture.

•  5.25’ power cord with plug, link up to 8 shoplight together.
•  Do not handle any energized fixture or attempt to energize any fixture with wet hands or while 

standing on a wet or damp surface or in water.

•  Assure that the fixture is mounted onto a structurally sound surface that will support the 

fixture.

•  The fixture is designed for use in a 120 VAC, 60Hz fused circuit. Do not use on a dimming 

circuit.

•  Do not look into the lights.
•  Product is intended for use in garages, basements, work areas, utility rooms and recreation 

rooms.

•  Maximum distance to the receptacle is determined by the length of the cord provided.
 

(5.25 ft, 3-prong, 120V grounded plug included)

•  Includes a protective sleeve, such as 0.010-inch (0.25-mm) thick fiberglass, where the path 

of cord travel to the ceiling-mounted receptacle is not between the two supporting chains.

•  The fixture is intended to be installed directly beneath a ceiling-mounted receptacle. Excess 

cord should be secured to one of the supporting chains with a cable tie to keep it out of the 
work space.

•  Use hook to support chain, not the electrical cord.
•  Do not install on radiant-heating type ceiling.
•  Maximum distance to the receptacle is determined by the length of cord provided.

WARNING: Failure to comply with these instructions could result in a potentially fatal electric 

shock and/or property damage.

•  Carefully remove the fixture from the carton and check to make sure that all hardware is included.
•  Be careful not to misplace any of the hardware needed for installing the fixture. If all hardware is 

not included, call customer service number.

NOTE: The unit is intended to be installed directly beneath a ceiling-mounted receptacle. If 

there is excess cord, bind with string or a cable tie to keep it out of work space.

ATTACH THE “S” HOOKS
Insert the “S” hooks (Part BB) into each of the holes on both sides of the shop Light.
(Figure 1)

NOTE: A maximum of 8 lights can be connected off of a single circuit.

 
  

 

 

1.  Using two hanging chains (Part AA) attach a hanging chain to one of the “S” hooks (Part BB) 

previously attached to each side of the light fixture. (Figure 2)

NOTE: The hanging chain must be bent in half in order to attach each side to an “S” hook.

2.   Attach two additional “S hooks” (Part BB) to the center of each hanging chain previously attached.
3.  Attach the remaining hanging chains (Part AA) to the “S” hooks (Part BB) previously attached.
4.  Adjust chain manually to achieve desired height.
5.  Attach the remaining “S” hooks (Part BB) to the hanging chains and attach to the ceiling hooks.
6.  Determine whether a single or multiple units are to be installed.  If multiple units will be 

installed follow steps in 

CONNECTION OPTIONS section. Connect lights per instructions and

repeat steps 1-5 (under Attach the Hanging Chain) for each light connected.

7. Plug power cord into an outlet to use pull chain to power on.

Maximum Weight: 7 kgs.

2.0 mm x 25.4 mm x 11.6 mm 

3.0 mm x 54.5 mm x 15.6 mm

(Figure 1)

Fold

Fold

Fold

Fold

 

AUX IN

Power Cord 

Plug 

AUX OUT

Reflex Port

Reflex Port

NOTE:  When linking shop lights, you should pair your Bluetooth with the first one in the 
linking chain, then connect all linked lights with provided aux cables.  Only 1 light will be 
able to paired from a single device.

Bluetooth Speaker will enter pairing mode when you turn on the light. Activate bluetooth on 
your device and find device named BT0445DS0620. Press to pair. 
The Bluetooth Speaker will turn off when the light is turned off.

1. 

2. 

Up to 8 units can be connected using the 5.25" power cord.  Once installed, plug the power 
cord into the end of linked shop light and repeat up to 7 times.

To link the audio in up to 8 shop lights connect the audio cable (Part EE) from the aux out 
on first shop light and then into the aux in on second shop light.  Repeat for up to 8 lights.

1.  

2. 

 Length 1.5m

   AC Outlet

 

 

Connect the power cord 

plug to shoplight 

   AUX IN

   AUX OUT

Connect ends of audio cable (Part EE) from 

Aux Out to Aux In on each linked shoplight

(Figure 2)

Bluetooth Speakers

AC Outlet

For better operation, the distance between Bluetooth device and the shop light had better less than 
65.6ft(20m)(It depends on the Bluetooth device and the environment).

65.6ft (20m)

Choose desired location of light fixture making sure it is within reach of an outlet. Use a pencil 
to place a mark on the ceiling where each ceiling hook (Part CC) should go. Screw hooks in 
place until secure.

MAX. 8 Units 

Only Connect To Adjacent Light Fixture

MAX. 8 Units 

Only Connect To Adjacent Light Fixture