Справочник Пользователя для Dongguan Xinliang Co. Ltd X30EARPHONE
instructions, may cause harmful interference to radio
communications.
communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
Warning: Changes or modifications to this unit not expressly
approved by the part responsible for compliance could void the
user’s authority to operate the equipment.
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
Warning: Changes or modifications to this unit not expressly
approved by the part responsible for compliance could void the
user’s authority to operate the equipment.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure
requirement.
The device can be used in portable exposure condition without
restriction.
FCC ID:2AQUKX30EARPHONE
The device has been evaluated to meet general RF exposure
requirement.
The device can be used in portable exposure condition without
restriction.
FCC ID:2AQUKX30EARPHONE
Before the first ues of bluetooth headset battery must be full
of charge firstly
1.The charger wire connected to the charging socket on the
headset.
2.Insert the charger into the power switch.
3.The charging indicator light shows red, once fully charged ,
the blue light glows.
4.To isolate the charger from the headset and power socket.
5.The charging is complete.
1.Boot:hold down the start/end call button for about 6 seconds,
untilthe alternating red and blue.
2.To turn it off:hold down the start/end call about 3 seconds,
until closed.
To charge Battery
ON/OFF switch machine
Chinese and English switching
1.After the headset is turned on, press the function key for
2 times.
1.Open the headset,hold down the function keys about 6
seconds to red and blue lights flashing.
2.Set the phone to search for bluetooth devices.
3.When the phone search to headphones,search to the list to
determine the headphones.
4.If the pairing is successful.blue lights will flash ,at this point
the standby mode are ready to dial/accept the call.
Press the start/end call
button on the headset.
Press the start/end call
button on the headset.
When the phone rings continue to hold the start/end call button
on the the headphones for about 2 second.
To pair the Headset With a Biuetooth Enabled Phone
To Answer a Call
To end a call
To Reject a Call
To Redial the Last called Number
1.In standby mode click headsets start/end call for about 2
seconds to loosen.
1.Long press the "+" key to change the previous song.
2.Long press the "-" key to change the next song.
1.Short press the"+" key to increase the volume.
2.Short press the "-" key to reduce the volume.
Song switch up and down
To Adjust Volume of Headset
Warning
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the in
energy and, if not installed and used in accordance with the in
PURPLELEAFLI
Product:wireless earphone
Model:X30