Справочник Пользователя для Orion Electric Co Ltd M2E5A
10
Basic connections
75 ohm coaxial
cable (supplied)
cable (supplied)
DVD/VCR
Splitter 75 ohm input
75/300 ohm outputs
(not supplied)
75/300 ohm outputs
(not supplied)
DVD/VCR
75 ohm coaxial cable
(supplied)
(supplied)
Splitter 75 ohm input
300 ohm output
(not supplied)
300 ohm output
(not supplied)
DVD/VCR
75 ohm coaxial cable
(supplied)
(supplied)
This DVD/VCR has a single 75 ohm output for connection to a
TV. If your TV has separate VHF and UHF antenna inputs (num-
bers 2 and 3 below), use a splitter to connect the DVD/VCR to
the TV for VHF and UHF reception.
TV. If your TV has separate VHF and UHF antenna inputs (num-
bers 2 and 3 below), use a splitter to connect the DVD/VCR to
the TV for VHF and UHF reception.
Antenna to DVD/VCR connection
The DVD/VCR must be connected “between” the antenna and
the TV. First, disconnect the antenna from the TV and connect
it to the DVD/VCR. Then connect the DVD/VCR to the TV.
Below are 3 common methods of connecting an antenna sys-
tem to a DVD/VCR. Find the type of antenna system you are
using and follow the connection diagram.
the TV. First, disconnect the antenna from the TV and connect
it to the DVD/VCR. Then connect the DVD/VCR to the TV.
Below are 3 common methods of connecting an antenna sys-
tem to a DVD/VCR. Find the type of antenna system you are
using and follow the connection diagram.
DVD/VCR to TV connection
After you have connected the antenna to the DVD/VCR, you
must connect the DVD/VCR to the TV.
Below are 3 common methods of connecting your DVD/VCR
to a TV. Find the type of TV you are using and follow the con-
nection diagram.
must connect the DVD/VCR to the TV.
Below are 3 common methods of connecting your DVD/VCR
to a TV. Find the type of TV you are using and follow the con-
nection diagram.
Example 1:
Combination VHF/UHF antenna with 75 ohm
coaxial cable
coaxial cable
Example 2:
Combination VHF/UHF antenna with 300 ohm
twin lead (flat) wire
Example 3: Separate VHF and UHF antennas
NOTE:
If both VHF and UHF antennas have 300 ohm twin lead (flat)
wires, use a combiner having two 300 ohm inputs and one 75
ohm output.
If both VHF and UHF antennas have 300 ohm twin lead (flat)
wires, use a combiner having two 300 ohm inputs and one 75
ohm output.
NOTES:
• A clear picture will not be obtained by the main unit unless
• A clear picture will not be obtained by the main unit unless
the antenna signal is good. Connect the antenna to the
main unit properly.
main unit properly.
• For better quality recording, an indoor antenna or a telescopic
antenna is not recommended. The use of an outdoor type
antenna is required.
antenna is required.
• If you are not sure about the connection, please refer to
qualified service personnel.
Example 1:
TV with single 75 ohm VHF/UHF antenna
input
input
Example 2: TV with 300 ohm UHF and 75 ohm VHF
antenna inputs
Example 3: TV with 300 ohm UHF and 300 ohm VHF
antenna inputs
75 ohm coaxial
cable
cable
DVD/VCR
OUT
(TV)
IN
(ANT)
300 ohm twin lead
(flat) wire
(flat) wire
DVD/VCR
Matching transformer
300 ohm input 75 ohm
output (not supplied)
300 ohm input 75 ohm
output (not supplied)
OUT
(TV)
IN
(ANT)
VHF UHF
DVD/VCR
300 ohm twin
lead (flat) wire
lead (flat) wire
75 ohm coaxial
cable
cable
Combiner
75/300 ohm inputs
75 ohm output (not supplied)
75/300 ohm inputs
75 ohm output (not supplied)
OUT
(TV)
IN
(ANT)
VHF/UHF
IN (ANT)
OUT
(TV)
IN
(ANT)
OUT
(TV)
IN
(ANT)
UHF
VHF
OUT
(TV)
IN
(ANT)
UHF
VHF
NOTE:
If a VHF or UHF antenna is used, set the TV/CABLE menu
option to the “TV” mode.
If a VHF or UHF antenna is used, set the TV/CABLE menu
option to the “TV” mode.
TV
TV
TV
2E50401A[E](10-17)
9/1/04, 10:05
10