Справочник Пользователя для ICOM 376800
– 2 –
– 3 –
D About the Status indicator
• Lights red while transmitting.
• Lights green while receiving a signal, or when the squelch is
open.
PANEL DESCRIPTION
D About the Microphone connector
Connect the supplied or optional microphone.
NEVER
connect non-specifi ed microphones. The pin
assignments may be different and may damage the
transceiver.
transceiver.
Speaker
[VOL]
Status
indicator
indicator
Microphone
connector
connector
Function
display
display
[OK] [Emer]
[Up]/[Down]
[Right]/[Left]
[Right]/[Left]
[Back]
[P1]
[P2]
Power key
F1
F2
F3
[VOL]
Microphone
connector
connector
Function
display
display
[Emer]
Power key
Speaker
[Up]
[Down]
[F1] [F2]
[F3]
Status
indicator
indicator
REAR PANEL CONNECTION
LCD type
Segment type
Antenna
12 V
Battery
Battery
q
e
r
u
t
Solder
Crimp
NOTE: Use the terminals as shown
below for the cable connections.
below for the cable connections.
w
Black
Red
y
ANTENNA CONNECTOR
Connect to an antenna. Contact
your dealer about antenna selection
and placement.
Connect to an antenna. Contact
your dealer about antenna selection
and placement.
q
w
D-Sub 25-pin
Connects to an external unit.
Connects to an external unit.
t
GPS ANTENNA CONNECTOR
Connect the UX-241 GPS antenna.
Connect the UX-241 GPS antenna.
e
IGNITION LEAD
Connects to an ignition line.
Connects to an ignition line.
Do not put pressure on this
lead. Binding to the DC power
cable is recommended.
lead. Binding to the DC power
cable is recommended.
u MICROPHONE HANGER
For a non-self-grounding type:
Connect the supplied microphone hanger
to the vehicle’s ground for microphone
ON/OFF hook functions.
For a self-grounding type:
The microphone ON/OFF hook functions
can be used without the vehicle’s ground.
Connect the supplied microphone hanger
to the vehicle’s ground for microphone
ON/OFF hook functions.
For a self-grounding type:
The microphone ON/OFF hook functions
can be used without the vehicle’s ground.
r
Connects to a 12 V DC battery.
Pay attention to polarities. NEVER connect
to a 24 V battery.
This will damage the transceiver.
Pay attention to polarities. NEVER connect
to a 24 V battery.
This will damage the transceiver.
i
i
EXTERNAL SPEAKER JACK
Connect a 4 ~ 8
Connect a 4 ~ 8
Ω external speaker.
R
R WARNING! NEVER
remove the fuse
holders from the DC
power cable.
remove the fuse
holders from the DC
power cable.
y USB CABLE
Connects to a PC.
Fuse holders
User supplied
Connect the microphone
hanger to the vehicle’s
ground for microphone
ON and OFF hook
functions when the
HM-221/HM-221T
microphone is used.
hanger to the vehicle’s
ground for microphone
ON and OFF hook
functions when the
HM-221/HM-221T
microphone is used.
When using a self-grounding type:
Non-self-grounding type
Self-grounding type
NOTE: Different functions may have been assigned to the keys by your dealer, except for the Power key.
D Turning power ON
Hold down [ ] for 2 seconds to turn ON the transceiver.
D Receiving and Transmitting
Receiving:
1. Push [Up] or [Down] to select a channel.
2. When receiving a call, rotate [VOL] to adjust the audio
1. Push [Up] or [Down] to select a channel.
2. When receiving a call, rotate [VOL] to adjust the audio
output level to a comfortable listening level.
Transmitting:
1. Wait until the channel is clear to avoid interference.
2. While holding down [PTT], speak at your normal voice
1. Wait until the channel is clear to avoid interference.
2. While holding down [PTT], speak at your normal voice
level.
3. Release [PTT] to receive.
IMPORTANT:
To maximize the readability of your signal:
1. After pushing [PTT], pause briefl y before you start
To maximize the readability of your signal:
1. After pushing [PTT], pause briefl y before you start
speaking.
2. Hold the microphone 5 ~ 10 cm (2 ~ 4 inches) from your
mouth, then speak at your normal voice level.
BASIC OPERATION
OPTIONS
• RMK-5
SEPARATION
KIT
+ OPC-2364
SEPARATION
CABLE
Enables you to separately install the transceiver’s main
unit from the front panel for convenient operation.
• RMK-7
DUAL
HEAD
KIT
+ OPC-2364
SEPARATION
CABLE
Enables you to separately install the transceiver’s main
unit from the front panel for convenient operation.
• SP-30, SP-35, SP-35L
EXTERNAL
SPEAKERS
Input impedence: 4 Ω
SP-30:
SP-30:
Rated input= 20 W, Maximum input = 30 W
SP-35/SP35L: Rated input= 5 W, Maximum input = 7 W
• HM-218, HM-220, HM-220T, HM-221, HM-221T
HAND
MICROPHONES
HM-218: Command microphone with a built-in speaker
HM-220: Self-grounding heavy duty microphone
HM-220T: Self-grounding heavy duty DTMF microphone
HM-221: Hand microphone
HM-221T: DTMF microphone
HM-220: Self-grounding heavy duty microphone
HM-220T: Self-grounding heavy duty DTMF microphone
HM-221: Hand microphone
HM-221T: DTMF microphone
• SM-29
DESKTOP
MICROPHONE
• UX-241
GPS
ANTENNA
Enables you to use the GPS function.