Справочник Пользователя для Swiscare Technology Co. Ltd. GM20NBLE
Intended for use
Ecare IA
The
Blood Glucose Monitoring Systems is intended for the
quantitative measurement of glucose in fresh venous whole blood,
or in fresh capillary whole blood from the fingertip. It is intended people
with diabetes mellitus at home or healthcare facilities for monitoring
the effectiveness of diabetes control program. It is not intended for the
diagnosis of or screening for diabetes mellitus, and is not intended for
use on neonates.
or in fresh capillary whole blood from the fingertip. It is intended people
with diabetes mellitus at home or healthcare facilities for monitoring
the effectiveness of diabetes control program. It is not intended for the
diagnosis of or screening for diabetes mellitus, and is not intended for
use on neonates.
Test Principle
The
The
blood glucose monitoring system is plasma calibrated
Ecare IA
to allow easy comparison of results with laboratory methods. Glucose in
the blood sample mixes with special chemicals on the test strip and a
small electrical current is produced. This current is measured by the
the blood sample mixes with special chemicals on the test strip and a
small electrical current is produced. This current is measured by the
Meter and displayed as your blood glucose result. The strength
Ecare IA
of these currents changes with the amount of glucose in the blood sample.
of these currents changes with the amount of glucose in the blood sample.
Ecare IA Blood Glucose Test strip
Note
1.
1.
Meter should only be used with
Blood Glucose Test Strip. Using
Ecare IA
Ecare IA
other test strips with this meter can produce inaccurate results.
2.The front side of the
2.The front side of the
Blood Glucose Test Strip should face up when inserting
Ecare IA
the
Blood Glucose Test Strip.
Ecare IA
3.The strips are for single use only, please do not reuse or use the used strip and repeat the test.
Please insert the test strip The temperature is out of range
Please apply blood to the strip Control solution mode
Measurement Unit
Milligram per Deciliter
Millimole per Liter
1. Ecare IA Meter × 1 .Lancet device × 1 3. Ecare IA Blood Glucose
Test Strip vial × 1
Test Strip vial × 1
4. Lancet × 10 5.Ecare GDH Control Material 6.AAA Alkaline Battery
(Optional)
(Optional)
Protective cover
Lancet point
Operation of Lancing device
• Alternative site testing means that people test blood glucose from the forearm,
upper arm or finger tip.
upper arm or finger tip.
• Please consult your doctor to determine if alternative site testing is right for
you.
you.
Select a soft, fleshy area of skin that is free from hair, moles and visible
•
veins for alternative site testing.
veins for alternative site testing.
Avoid lancing areas with obvious veins or moles to avoid excess bleeding
•
or where tendons or bones stick out (for example, hand bones and ankle
bones)
or where tendons or bones stick out (for example, hand bones and ankle
bones)
AST alternate site testing
It is strongly recommend that do AST ONLY in the following intervals
-In a pre-meal or fasting state (more than 2 hours since the last meal).
-Two hours or more after taking insulin.
-Two hours or more after exercise.
Do Not do AST
-You think your blood glucose is low.
-You are unaware of hypoglycemia.
-Your AST results do not match how you feel.
-You are testing for hyperglycemia.
-Your routine glucose results are often fluctuating.
-If you are pregnant.
-In a pre-meal or fasting state (more than 2 hours since the last meal).
-Two hours or more after taking insulin.
-Two hours or more after exercise.
Do Not do AST
-You think your blood glucose is low.
-You are unaware of hypoglycemia.
-Your AST results do not match how you feel.
-You are testing for hyperglycemia.
-Your routine glucose results are often fluctuating.
-If you are pregnant.
Run a control test by Ecare GDH Control Material (optional accessory)
when you open a new vial of test strips or if you think that your test
result is incorrect. Running a control test lets you know that the meter
and test strips are working properly.
when you open a new vial of test strips or if you think that your test
result is incorrect. Running a control test lets you know that the meter
and test strips are working properly.
IA Blood Glucose
Monitoring System
User’s Manual
2 AAA
1.Press S button 2 seconds into the setting mode.
(no test strip inserted).
Please follow the below steps to change the
parameters.
2.The “L-1” on the display.
Press "M" to select the languages(L-1~L-3)
,then press "S" to confirm language:
Press "M" to select the languages(L-1~L-3)
,then press "S" to confirm language:
3.The “3” on the display.
Press "M" to select the volume(3~0) ,
then press "S" to confirm volume:
3:high volume
0:mute
Press "M" to select the volume(3~0) ,
then press "S" to confirm volume:
3:high volume
0:mute
1.The year flashes on the display.
Press "M" to select the year(2015~2050)
,then press "S" to confirm year.
Press "M" to select the year(2015~2050)
,then press "S" to confirm year.
2.Repeat the same steps to set
the month, date ,hour and minute.
the month, date ,hour and minute.
Note
The hour format is the
12-hour time.
The hour format is the
12-hour time.
Memory
symbol
symbol
Control
Solution
Mode
Solution
Mode
Set the measurement unit
1.The measurement unit flashes.
2.Set the measurement unit:
Press "M"to select the unit :mg/dL or mmol/L.
Press "M"to select the unit :mg/dL or mmol/L.
3.Press "S" to confirm measurement unit.
Note
1. The unit can be changed in setting mode.
2. If you can not change unit during step 2, it means the
system was fixed the unit by default setting.
2. If you can not change unit during step 2, it means the
system was fixed the unit by default setting.
1. Wash hands with soap and warm water.
Rinse and dry thoroughly.
Rinse and dry thoroughly.
2. Pull out a test strip from the box and
must re-cap the box immediately.
must re-cap the box immediately.
3. Insert the test strip, the front side of the
test strip face up, into the test port.
The meter will automatically turn on.
test strip face up, into the test port.
The meter will automatically turn on.
1. The “dEL” display, press “S” goes to sleep
mode.
mode.
2. Or press “M” 2 sec, it displays “OK”
to delete all memory, then goes to
sleep mode.
to delete all memory, then goes to
sleep mode.
Delete the test result
Preparing your blood sample
1. Wash your hands with soap and warm water.
Then rinse and dry thoroughly.
2. Massage the puncture site.
3. Using lancet device firmly on the side of the fingertip
to get a drop of blood.
4. Press the button on the lancet device.
The blood has been taking as you hear a click sound.
5. Gently squeeze or massage your finger until drop of
blood forms.
Then rinse and dry thoroughly.
2. Massage the puncture site.
3. Using lancet device firmly on the side of the fingertip
to get a drop of blood.
4. Press the button on the lancet device.
The blood has been taking as you hear a click sound.
5. Gently squeeze or massage your finger until drop of
blood forms.
Note
• The user must wash hands thoroughly with soap and water after handling
the meter, lancet device or test strips.
• The lancets can not to be re-used or used more than one person to increase
the infection risk.
• Don’t use Povidone Iodine Solution or any org nic solvent for cleaning!
• Wait until hands dry completely!
• The user must wash hands thoroughly with soap and water after handling
the meter, lancet device or test strips.
• The lancets can not to be re-used or used more than one person to increase
the infection risk.
• Don’t use Povidone Iodine Solution or any org nic solvent for cleaning!
• Wait until hands dry completely!
Note
1. Please do not touch on the strip by your finger or use
the smearing blood sample.
2. Do not remove the strip before complete 6 seconds
count down, or it will be automatically shut down.
3. The test strips cannot be re-used.
1. Please do not touch on the strip by your finger or use
the smearing blood sample.
2. Do not remove the strip before complete 6 seconds
count down, or it will be automatically shut down.
3. The test strips cannot be re-used.
Blood glucose
120 mg/dL.
Now Testing.
Contr ol Solut ion M ode.
Please apply blood
into the test strip.
1. Inserting the test strip.
3. Put your blood drop to the Reaction Area on the strip.
4. After dropping the blood , you will hear a beep sound, then it
starts 6 seconds count down at the same time.
starts 6 seconds count down at the same time.
5. The result will appear on the display,
auto-saving in memory.
auto-saving in memory.
6.Remove the used test strip, then it goes to sleep mode.
2. Press “M” button to highlight your status
as “control mode ”, “before meals ”,
“after meals ” or in general mode without
labeling.
a) Pressing once “M” button highlights the
value with as control solution mode.
(Testing results in control solution mode
will not store in memory.)
b) Pressing once “M” button highlights the
value with as before meals status.
c) Pressing once “M” button highlights the
value with as after meals status.
d) Pressing one more “M” button removes the
highlight with general mode.
as “control mode ”, “before meals ”,
“after meals ” or in general mode without
labeling.
a) Pressing once “M” button highlights the
value with as control solution mode.
(Testing results in control solution mode
will not store in memory.)
b) Pressing once “M” button highlights the
value with as before meals status.
c) Pressing once “M” button highlights the
value with as after meals status.
d) Pressing one more “M” button removes the
highlight with general mode.
LCD Display
36.4 44.4
x
Insert test strip here
Battery cover
Label
For Model : GM20E