Справочник Пользователя для Shenzhen Skylark Audio Industry Co. Ltd. F1BASE
User Manual
Model: F1
Levitating Speaker
OFF ON
1. Top colorful decorative LED
2. Work status LED
Blue light: flashing means
Bluetooth pairing mode,
light stably means Bluetooth
connected
Green flashing: Low battery,
please charging
Red light: it works while
battery is charging, turned
off while battery is filled
3. Power switch
4. Micro USB: charging in socket
Ball description
1
OFF ON
2
3
4
4
OFF
ON
Please stop placing ball to levitate on subwoofer when you try it many times,
otherwise, the electromagnetic servo system would be overheated and pr-
otection circuit is turned on while subwoofer temperature exceeds 75 deg-
rees Celsius, please try it again after 10 minutes.
Please pick up the ball and adsorb it on the top of subwoofer before you
unplug the subwo-ofer DC power. Ball will fall down when subwoofer power
cut accidentally.
The F1 should be put away more than 80cm from phones, computers, bank
cards and any objects easily magnetized because there are permanent
magnets in it. Avoid using F1 in the severe electromagnetic environment,
such as iron table.
This is not a toy and it is not suitable for the children under 12 years old to use .
Special notice
1. Ball can't be turned on.
Check the power switch is pushed to ON position; please charge it when
the ball is low battery.
2. Can't search F1 in BT device list on phone.
Please observe the work status LED of ball; it's connected when blue LED
is light on. In this case, ball is forced into pairing state when long press
button on the subwoofer panel.
3. Ball can't be levitated.
Check whether the subwoofer is placed on iron table or other magnetic
objects; make sure the power adapter is plugged into the subwoofer DC-
12V socket, Check whether the 4 LEDs in center ring of subwoofer are lit,
Operate it according to manual.
4.
Please turn on the base and ball, make sure the ball is levitated on the base,
and the ball battery voltage is normal, otherwise,it can't work.
Trouble shooting
OFF ON
OFF ON
Remove positioning
mat, Ball is levitated
successfully
mat, Ball is levitated
successfully
Long press on base panel, WORK LED and
ball top LED is lit. F1 re-connect last used ph-
one firstly, work status blue LEDlit stable mea-
ns re-connect successfully, flashing means re-
connect failure, waiting for other phone to co-
nnect, Please longpress to make F1 entering
into another phone pair status, if you like to
change using
ball top LED is lit. F1 re-connect last used ph-
one firstly, work status blue LEDlit stable mea-
ns re-connect successfully, flashing means re-
connect failure, waiting for other phone to co-
nnect, Please longpress to make F1 entering
into another phone pair status, if you like to
change using
6
5
How to operate
Please place the subwoofer on
an level table, Connect the power
adapter to the subwoofer and turn
it on.
Put the positioning mat on the
center of the subwoofer.
center of the subwoofer.
1
2
OFF ON
OFF ON
OFF ON
Put down the ball on the mat center
vertically by 2 hands hold it, you can
loosen ball slowly after the 4 positioning
LEDs lit which on the left side of
subwoofer
vertically by 2 hands hold it, you can
loosen ball slowly after the 4 positioning
LEDs lit which on the left side of
subwoofer
4
3
Shenzhen Skylary Audio Industry Co.,Ltd.
5. To change work mode of ball top LED lights, LED mode is cycle of
breathing mode>> music mode>>turn off
6. POWER : Red, to indicate the status of turn on or off
7. WORK : Green, to indicate the speaker work normally
8. TX : Blue, to indicate the commands is transmitted from subwoofer to ball.
9. RX : Blue, to indicate the commands is received from ball to subwoofer
10.
breathing mode>> music mode>>turn off
6. POWER : Red, to indicate the status of turn on or off
7. WORK : Green, to indicate the speaker work normally
8. TX : Blue, to indicate the commands is transmitted from subwoofer to ball.
9. RX : Blue, to indicate the commands is received from ball to subwoofer
10.
Position Aid :
Assisted positioning LEDs
Levitate heigh:About15mm
Power adapter : DC 12V/2.5A
Bluetooth version:V4.0
Bluetooth version:V4.0
SNR : >80 dB
Frequency response:60HZ-20KHZ
Ball Li battery:1200mAh
Work time : 5 to 8 hours
Ball size:D 77 * H 86 mm
Ball Li battery:1200mAh
Work time : 5 to 8 hours
Ball size:D 77 * H 86 mm
Subwoofer size:L 174*W 174*H100mm
Inner carton:L223*W223*H234mm
G.W:About 2.3kg
Inner carton:L223*W223*H234mm
G.W:About 2.3kg
Technical Parameter
10. OFF-ON Power switch.
11. DC-12V Power input socket.
12. OUT 5V USB charging out for
ball speaker or other devices.
11. DC-12V Power input socket.
12. OUT 5V USB charging out for
ball speaker or other devices.
10
12
11
Back panel
1.
Long press: Turn on or off
2.
Volume reduce.
3.
Long press: Entering into
Bluetooth pairing status
4.
Volume increase
Front panel
Packing list
OFF ON
manual
Turn on the ball speaker
1.
2.
3.
4.
6
7 8
2
3
9
1
4
5
10
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in
portable exposure condition without restriction.
portable exposure condition without restriction.