Листовка для Transition Networks C2110-1011

Ordering Info

C2110-1011

100BASE-TX (RJ-45)

[100 m/328 ft.]

to 100BASE-FX 1300nm MM (ST)

[2 km/1.2 mi.] Link Budget: 11.0 dB

C2110-1013

100BASE-TX (RJ-45)

[100 m/328 ft.]

to 100BASE-FX 1300nm MM (SC)

[2 km/1.2 mi.] Link Budget: 11.0 dB

C2110-1039

100BASE-TX (RJ-45)

[100 m/328 ft.]

to 100BASE-FX 1300nm MM (LC)

[2 km/1.2 mi.] Link Budget: 11.0 dB

C2110-1014

100BASE-TX (RJ-45)

[100 m/328 ft.]

to 100BASE-FX 1300nm SM (SC)

[20 km/12.4 mi.] Link Budget: 16.0 dB

C2110-1019

100BASE-TX (RJ-45)

[100 m/328 ft.]

to 100BASE-FX 1300nm SM (LC)

[20 km/12.4 mi.] Link Budget: 17.3 dB

C2110-1015

100BASE-TX (RJ-45)

[100 m/328 ft.]

to 100BASE-FX 1300nm SM (SC)

[40 km/24.9 mi.] Link Budget: 29.0 dB

C2110-1016

100BASE-TX (RJ-45)

[100 m/328 ft.]

to 100BASE-FX 1300nm SM (SC)

[60 km/32.3 mi.] Link Budget: 29.0 dB

C2110-1017

100BASE-TX (RJ-45)

[100 m/328 ft.]

to 100BASE-FX 1550nm SM (SC)

[80 km/49.7 mi.] Link Budget: 29.0 dB

C2110-1035

100BASE-TX (RJ-45)

[100 m/328 ft.]

to 100BASE-FX 1550nm SM (SC)

[120 km/77.5 mi.] Link Budget: 36.0 dB

C2110-1040

100BASE-TX (RJ-45)

[100 m/328 ft.]

to 100Base Open SFP

Single Fiber Products
Recommended use in pairs

C2110-1029-A1

100BASE-TX (RJ-45)

[100 m/328 ft.]

to 100BASE-FX 1310nm TX / 1550 nm RX

single fiber single mode (SC)

[20 km/12.4 mi.] Link Budget: 19.0 dB

C2110-1029-A2

100BASE-TX (RJ-45)

[100 m/328 ft.]

to 100BASE-FX 1550nm TX / 1310 nm RX

single fiber single mode (SC)

[20 km/12.4 mi.] Link Budget: 19.0 dB

C2110-1029-B1

100BASE-TX (RJ-45)

[100 m/328 ft.]

to 100BASE-FX 1310nm TX / 1550 nm RX

single fiber single mode (SC)

[40 km/24.9 mi.] Link Budget: 25.0 dB

C2110-1029-B2

100BASE-TX (RJ-45)

[100 m/328 ft.]

to 100BASE-FX 1550nm TX / 1310 nm RX

single fiber single mode (SC)

[40 km/24.9 mi.] Link Budget: 25.0 dB

Specifications

Standards

IEEE Std. 802.3

Data Rate

100MBps, Layer-1

Switches

SW1: Auto-Negotiation (UP = enabled)
SW2: Pause (UP=enabled)
SW3: Link Pass Through (UP = enabled)
SW4: Far-End-Fault (UP = enabled)

Internal Jumpers

AutoCross™: Enable/Disable

Hardware/Software Jumpers

Hardware: Mode of operation is determined by the

settings on the 4-position switch
Software: Mode of operation is determined by the
most recently saved on-board microprocessor settings

Status LEDs

PWR (Power): ON = Connection to powered backplane
LKC (Copper Link): ON = Copper Link
RXC (Receive Copper): Blinking = Data recieved on
Copper link
LKF (Fiber Link): ON = Fiber Link
RXF (Receive Fiber): Blinking = Data received on
Fiber Link

Dimensions

Width: 0.86” (22 mm)
Depth: 6.5” (165 mm)
Height: 3.4” (86 mm)

Power Consumption

2.5 Watts, 200mA @ 13.9VDC

Environment

See chassis specifications

Shipping Weight

1 lb. [.45 kg]

Regulatory Compliance

CISPR/EN55022 Class A, FCC Class A, CE Mark

Warranty

Lifetime

AUTO NEG

AUTO CROSS LINK PASS THRU FAR END FAULT LINK RESTORE

AUTO

PAUSE

UPGRADE

REMOTE FIRMWARE

SINGLE

FIBER

C2110 Series

The ION Platform

Fast Ethernet Media Converter
100BASE-TX to 100BASE-FX

Fiber Integration in 10/100 Copper environments

The ION C2110 device provides an interface between 100Base-TX ports
and 100Base-FX ports allowing users to integrated fiber optic cabling
into 100Base-TX copper environments.

Fast Ethernet

slide-in-module for the ion platform

Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA

tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com

©2010 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.

The following manageable features
are available when used in an ION
chassis along with an ION Manage-
ment Module

Report converter status to

chassis management software:

• TP and Fiber Link Status
• Hardware switch settings
• Fault condition
• TP cable length

Write operation includes:

• Power on/off device
• Auto-Negotiation enable/disable
• Pause enable/disable
• LPT enable/disable
• FEF enable/disable
• AutoCross enable/disable

Features

Auto-Negotiation of speed
and duplex on TP port

AutoCross™ on TP port

Link Pass Through (LPT)

fault monitoring

Far-End-Fault (FEF) detection

Automatic Link Restoration

Pause advertisement

Remote Firmware Upgrade

Can be used in any

ION Platform Chassis

Standards based, will link with any

standard 100Base-TX and any
standard 100Base-FX ports