Листовка для Transition Networks CBFTF1010-130
Point System™
Ordering Information
CBFTF1010-130
10/100BASE-TX Link Protector Transceiver
(3) 10/100BASE-TX (RJ-45)
[100 m/328 ft.]
Fault-Tolerant Redundant Connections
Specifications
Standards
IEEE Std. 802.3
RJ-45 Connectors
Type: 8-position, RJ-45 receptacle:
1: TX+
5: NC (no connection)
2: TX-
6: RX-
3: RX+
7: NC (no connection)
4: NC (no connection)
8: NC (no connection)
Dip Switches
SW1: Auto-Negotiation Enable/Disable
SW2: 10/100 Mbps
SW3: Full/Half Duplex
SW4: Redundancy/Switch
System LEDs
Power (PWR): Indicates the presence of POWER
Primary (PRI): Indicates a link is established on the
Primary port
Backup (BKP): Indicates the link has moved over to
the Backup port
Per Port LEDs
Lower Right:
Green indicates 100 Mbps;
Orange indicates 10 Mbps;
Flashing indicates Activity
Lower Left:
Green indicates full-duplex; Off half-duplex
Dimensions
Width: 0.86” [12 mm]
Depth: 5.0” [127 mm]
Height: 3.4” [86 mm]
Power Consumption
2.4 Watts
Environment
See chassis specifications
Shipping Weight
1 lb. [0.45 kg]
Regulatory
FCC Class A, EN55024, UL 60950,
Compliance
CE Mark
Warranty
Lifetime
CBFTF1010-130
CBFTF1010-130
point system™ slide-in-module media converter
The Redundant Link Protector is a 10/100
Ethernet fault-tolerant transceiver. It
Ethernet fault-tolerant transceiver. It
significantly reduces network down-
time, adding a new level of redundancy
to 10/100 Ethernet connections. It also
provides a redundant path for critical
10/100 devices. In a 10/100 Ethernet
network, a critical device such as a file
server may be connected to the rest of
the network through a hub or a switch. A
common problem in this configuration is
that the server is often connected to the
network through a single cable. If the cable
fails, then the server is disconnected from
the rest of the network. Similarly, if a port
of a hub or switch to which the server is
connected fails, the server is disconnected
from the network.
time, adding a new level of redundancy
to 10/100 Ethernet connections. It also
provides a redundant path for critical
10/100 devices. In a 10/100 Ethernet
network, a critical device such as a file
server may be connected to the rest of
the network through a hub or a switch. A
common problem in this configuration is
that the server is often connected to the
network through a single cable. If the cable
fails, then the server is disconnected from
the rest of the network. Similarly, if a port
of a hub or switch to which the server is
connected fails, the server is disconnected
from the network.
The Redundant Transceiver has three
ports: one for the critical (main) device, one
for the default (primary) path for the critical
device, and another (backup) for the
backup path. It is a smart device that will
not send any signal on a path that is not
active. If the primary path loses its
link, then the transceiver will switch to
the backup path in approximately 189
milliseconds.
When the primary path re-establishes its
link, the Redundant Link Protector will
automatically switch back to the primary
path.
Optional functionality, controlled via a dip
switch, allows the unit to move from the
fault-tolerant mode to a 3-port switch
mode.
ports: one for the critical (main) device, one
for the default (primary) path for the critical
device, and another (backup) for the
backup path. It is a smart device that will
not send any signal on a path that is not
active. If the primary path loses its
link, then the transceiver will switch to
the backup path in approximately 189
milliseconds.
When the primary path re-establishes its
link, the Redundant Link Protector will
automatically switch back to the primary
path.
Optional functionality, controlled via a dip
switch, allows the unit to move from the
fault-tolerant mode to a 3-port switch
mode.
10/100BASE-TX Redundant Link Protector
10/100
see also:
10/100 Redundant Link Protector Stand-Alone Media Converter
Fault-Tolerant Redundant Link Protector
Features
4
Fault-tolerant redundant connections
4
Easy to install and use
4
Supports half and full-duplex transmission
4
AutoCross™ on all 3 ports
4
Auto-Negotiation
4
IEEE 802.3 compliant
4
Nine diagnostic LEDs
4
Optional 3-port switch mode
4
Can be used with any Point System™ Chassis
The following management features are
available when the converter is used in a
managed Point System™ Chassis:
available when the converter is used in a
managed Point System™ Chassis:
4
Read Management features:
• Media Converter Power
• Copper Link Status
• Copper Port Speed
• Duplex Mode
• Hardware Switch Settings
• Copper Link Status
• Copper Port Speed
• Duplex Mode
• Hardware Switch Settings
4
Write Management features:
• Power on/off device
• Enable Redundancy/3-port Switch mode
• Enable Redundancy/3-port Switch mode
4
Individual Port Control:
• Enable/disable Auto-Negotiation
• Force Full or Half Duplex
• Force 10 Mbps or 100 Mbps
• Force Full or Half Duplex
• Force 10 Mbps or 100 Mbps
10/100BASE-TX Redundant Link Protector