Листовка для Transition Networks SPSVT2613-100 SPSVT2613-100-NA

Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA

tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com

©2011 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.

Ordering Information

Complete list of fiber optic connector specifications

Standards

ITU-T; ISO-2593

Data Rate

1.2 Kbps to 10 Mbps

Switches

Side panel, external DCE speed switch, sixteen
position: Speeds can also be set on DCE devices locally
or remotely via software
Front Panel, Loop-back Selector Switch: Right 
Position: Loop Fiber Back & Loop Copper Back
Left Position: Normal Operation

Internal Jumpers

Jumper (J4): Hardware: The terminal timing switch 
controls the terminal timing function. The loop-back 
switch controls the loop-back function.
Software: The terminal timing switch and the loop-
back switch are disabled. These two functions are 
controlled by the most recently saved, on-board 
micro processor settings.
Jumper (J6): RX Clock Polarity: Set to sample the 
receive data on the 

rising or falling edge of the 

receive clock.
Jumper (J7): TX Clock Polarity: Set to sample the 
transmit data on the 

rising or falling edge of the 

receive clock.

Status LEDs

The Copper LED uses a green LED
Smart Serial Link: Green - Link is up; 
Green Flashing - In loop-back mode; 
Fiber: Green - Link is up; 
Green Flashing - In loop-back mode; 
Power: Green - ON power applied to board

Dimensions

Width: 3.25" [82 mm]
Depth: 4.8" [120 mm]
Height: 1.0" [25 mm]

Power Consumption

5.0 Watts

Power

External AC/DC required; 12 VDC; 1A; regulated wall 
mount adapter via 2 mm connector

Environment

0 – 50°C, 5% – 90% humidity (non-condensing), 
0 – 10,000 ft.

Shipping Weight

2 lbs. [0.90 kg]

Safety Compliance

Wall Mount Power Supply: UL Listed and 
CSA certified

Regulatory Compliance

CISPR/EN55022, EN55024, EN60950 Class A; 
FCC Class A; CE Mark

Warranty

Lifetime

• 0 – TT = Receive CLK
• 1 – 56 Kbps
• 2 – 64 Kbps
• 3 – 112 Kbps
• 4 – 128 Kbps
• 5 – 256 Kbps
• 6 – 384 Kbps
• 7 – 512 Kbps

• 8 – 768 Kbps
• 9 – 1.024 Mbps
• A – 1.544 Mbps
• B – 2.048 Mbps
• C – 3.072 Mbps
• D – 4.096 Mbps
• E – 6.144 Mbps
• F – Asynchronous Mode

RS232/V.24

15 m

RS449/V.36

1.2 km

V.35

600 m

X.21

1.2 km

RS530

1.2 km

*For reference only. Contact Transition Networks 
for detailed range information.

Ordering Information

26-pin to 1300nm multimode (ST) 

26-pin to 1300nm multimode (SC)

26-pin to 1310nm single mode (SC)

26-pin to 1310nm single mode (SC)

[pg 19]

26-pin to 1310nm TX/1550nm RX 
single fiber single mode (SC)

26-pin to 1550nm TX/1310nm RX 
single fiber single mode (SC)

26-pin to 1310nm TX/1550nm RX 
single fiber single mode (SC)

26-pin to 1550nm TX/1310nm RX 
single fiber single mode (SC)

DB-15 (FT) (26-pin) to (DCE)

DB-15 (MT) (26-pin) to (DTE)

DB-25 (FT) (26-pin) to (DCE)

DB-25 (MT) (26-pin) to(DTE)

V.35 (FT) (26-pin) to (DCE)

V.35 (MT) (26-pin) to (DTE)

V.35 (MT) (26-pin) to (DTE)

DB-37 (FT) (26-pin) to (DCE)

DB-37 (MT) (26-pin) to (DTE)

DB-25 (FT) (26-pin) to (DCE)

DB-25 (MT) (26-pin) to (DTE)

Piggy Back Power Supply

Stand-Alone Power Supply

12-Slot Media Converter Rack

DIN Rail Bracket 5.0" [127 mm]

DIN Rail Bracket (flat) 3.3" [84 mm]

Wall Mount Bracket 4.0" [102 mm]

Vertical Wall Mount Bracket 5.0" [127 mm]

4-Slot Media Converter Shelf

stand-alone nid

Features

4

Connect High Speed Serial signals 

on copper to fiber

4

Supports multiple protocols through the 

use of a universal 26-pin serial 
interface connector

4

Extend the point of presence of a copper

V.35/X.21/RS449/RS530/RS232 
      connection at data rates up to 10 Mbps.

4

In-band Remote Management when used in 

conjunction with Point System™ card  

4

Operational speeds up to 10 Mbps

4

Copper & Fiber Loopback [pg 18]

4

Synchronous or asynchronous capability

4

Selectable DCE speeds

4

LED indications for Lock, Loopback & Data

4

Use a combination of any copper interface: 

(RS449 to V.35, RS530 to X.21, DTE-DTE, 
DTE-DCE, DCE-DCE, etc.) All interfaces 
converted at the physical level.