Справочник Пользователя для Toshiba RBC-AMS41E

GRUPAd.o.o.

19

• Change the settings of the remote controller functions 

as required by taking the steps below.

• The numeric displays and 

 display blink, 

and the fixed louvers display lights. 

• Repeatedly push the buttons until the setting to be 

changed blinks on the display.

• Repeatedly push the buttons until the setting to be 

changed blinks on the display.

• When the 

 button (42) is pushed, the numeric 

displays and 

 display stop blinking and 

light up, and when the 

 button (43) is pushed 

again, they go off.

• 24-hour/12-hour display setting <code No.10>

– The 24-hour display or 12-hour (AM/PM) display 

can be selected for the clock which is displayed on 
the remote controller.

– This item’s selection is also reflected on the clock 

displayed on the clock setting screen and program 
input screen.

• Restriction on button operations <code No.12>

This item sets the range of the restriction placed on 
the button operations which can be applied while 
scheduled operations are being performed.
Setting: 0000 (factory setting)

Code No.12
O: Can be operated.
X: Cannot be operated. 

• Display/non-display of clock <code no.13>

This item selects and sets whether the day of the week 
and clock time are to be displayed.
Setting: 0000 (factory setting)

Code No.13
O: Display   X: No display

• Selection of operation when power is restored after a 

power outage <code No.14>
This item selects the operation to be performed when 
power is restored after a power outage occurred 
during a scheduled operation.
0000: No operations are performed when the power is 
restored, and the scheduled operation is resumed as 
soon as the program time is reached after the power 
has been restored. (When the power is restored, the 
scheduled operation is based on the operation of the 
indoor units.)
0001: If there was a programmed operation during the 
power outage, that operation is performed when the 
program is resumed. If there is no programmed 
operation or if the “Continue xx” setting is in place, the 
operation prior to the power outage is resumed.

• The following functions can be selected using the DIP 

switches on the remote controller’s circuit board.

• Open the back cover of the remote controller, and 

select the functions using the DIP switches located at 
the bottom left of the circuit board.

• After establishing the settings, turn the ground fault 

interrupter off and then back on.

• Remote controller header/follower setting: Bit 1

When operating the air conditioner using two remote 
controllers, set one of the controls to be the follower.
* Set the remote controller used as the schedule timer 

to be the header. 

• Operation function setting: Bit 2

One of the following three operation functions can be 
selected and set.
1.Scheduled operation function
2.Timer operation function
3.No scheduled or timer operation function

Setting

Description

0000:
0001:

24-hour display (factory setting)
12-hour (AM/PM) display

Setting

[ON/OFF]

[MODE]

[TEMP.]

0000

O

O

O

0001

X

O

X

0002

X

X

X

0003

O

X

X

0004

O

X

O

Setting

Scheduled operation 

underway

Scheduled operation 

in standby

Air 

conditioner 

now 

operating

Air 

conditioner 

now shut 

down

Air 

conditioner 

now 

operating

Air 

conditioner 

now shut 

down

0000

O

O

O

O

0001

X

X

X

X

0002

O

O

X

X

0003

O

X

X

X

0004

O

O

O

X

0005

O

X

O

X

MB FRIGO Grupa d.o.o., Bani 81, 10010 Zagreb, www.toshiba.hr, e-mail: toshiba@mbfrigo.hr