Справочник Пользователя для Toshiba NG-ATH18
Next Generation Home Products manual • version 1.0 • page 2
11
TV/VCR COMBO CODES
12
SATELLITE CODES
14
RECALLING A DEVICE CODE
Perform the following steps to read the code currently set for a device. This is useful for retrieving
a device code that was set using the CodeScan
a device code that was set using the CodeScan
™
method.
Aiwa
251
Audio Dynamics
238
Broksonic
219 • 226
Curtis Mathes
231 • 241
DBX
238
Daewoo
247 • 250 • 252
Electrohome
240
Emerson
219 • 223 • 226 • 251 • 253
Funai
251
General Electric
231 • 233 • 241 • 248
Goldstar
223 • 230 • 238 • 254
Harman Kardon
238
Hitachi
231 • 241 • 251
JC Penney
223 • 231 • 238 • 241 • 242
JVC
234 • 235 • 238
Kenwood
235 • 251
LXI
223 • 251 • 254
MGA
240
Magnavox
231 • 236 • 237 • 241 • 251
Marantz
237 • 238
Marta
223
Memorex
223 • 242 • 244 • 245 • 248 • 251
Mitsubishi
239 • 240
Optimus
242
Orion
219 • 226
Panasonic
231 • 241 • 242
Philco
236 • 237 • 251
Philips
223 • 236 • 237 • 251
Pioneer
235
Proscan
233
Pulsar
248
Quasar
231 • 241 • 242
RCA
231 • 233 • 241 • 251
Radio Shack
230 • 242
Realistic
223 • 251
Runco
243
Samsung
221 • 244 • 245 • 246 • 247
Sansui
219 • 235
Sanyo
244 • 245
Scott
247
Sears
223
Signature
251
Sony
232
Soundesign
251
Sylvania
237 • 240 • 251
Symphonic
251
Tandy
251
Teac
251
Technics
242
Teknika
223 • 251
Toshiba
240 • 247
Totevision
223
Vector Research
238
Victor
235
Video Concepts
238 • 251
Wards
251
Yamaha
238 • 251
Zenith
219 • 223 • 235 • 248 • 249 • 251
4DTV
121
Alphastar
125
Amway
139
Birdview
235
CI Satellite
146
Cable Innovations
183
Century
148
Channel Master
147
Chaparral
214 • 215 • 216 • 217
Cheyenne
216
Citoh
145
Conifer
142
Curtis Mathes
174
DIRECTV
124 • 132 • 093 • 094 • 095 • 096 • 097 • 098
DISH Network
119
DISHPlayer
100
DX Antenna
115 • 144 • 213
Drake
149 • 187 • 188 • 189 • 191 • 194
Echostar
113 • 119 • 137 • 150 • 204 • 205 • 206 • 207 • 208
Express VU
119
Fujitsu
186
General Instrument
121 • 122 • 134 • 151 • 152 • 153 • 154
171 • 172 • 183 • 196 • 197 • 202
Hitachi
124 • 132
Homecable
226
Houston Tracker
113
Hughes Network
124 • 132 • 093 • 094 • 095 • 096 • 097 • 098
IQ
212
Insight
124
Intersat
241
JVC
119
Janeil
178 • 186
Kenwood
243
Legend
137 • 204
Macom
134 • 174
Magnavox
117 • 126
Memorex
117 • 137
Next Level
122
Norsat
142
Optimus
117
Orb
223
Panasonic
123 • 178
Pansat
246
Philips
117 • 126 • 176
Pico
139
Primestar
049 • 115
Prosat
138
Proscan
110 • 116 • 141
Quick Draw
144
RCA
110 • 116 • 141
Radio Shack
183 • 196 • 197
Ramsey
139
Realistic
230
Rural Cable
196
STS
212 • 213
Samsung
108
Sierra
216
Sony
112
Star Choice
122
Star Sight
109
Star Trak
136 • 218 • 219 • 222 • 223
Strong
136
Super Guide
253
TCE
110
TeeCom
248 • 251
Toshiba
133 • 134 • 174 • 187
Uniden
117 • 126 • 180 • 181 • 182 • 183 • 184
224 • 226 • 227 • 228 • 230 • 232
Video Cipher II
186
Viewstar
185
Zenith
149 • 174 • 186
15
Problem
I programmed the remote, but it won’t work my TV, VCR, or Satellite Receiver.
Solution
You may have entered the wrong code (or the correct code might not be listed). Try the
You may have entered the wrong code (or the correct code might not be listed). Try the
Code
Scan
™
procedure. It will allow you to cycle through all the codes until you find one that works.
Weak batteries may cause the remote to only operate one device or operate intermittently.
Replace weak batteries with
Replace weak batteries with
NEW alkaline batteries. If you are sure the batteries are good, try
rolling them with your finger (while they are in the remote control) to ensure a good connection.
Finally, make sure that nothing is blocking the signal from the remote control from reaching
your TV, VCR, or Satellite Receiver; and make sure that you are pointing the remote control at
the correct device when you are pressing a key on the remote.
your TV, VCR, or Satellite Receiver; and make sure that you are pointing the remote control at
the correct device when you are pressing a key on the remote.
Problem
My remote control doesn’t operate my combination TV/VCR.
My remote control doesn’t operate my combination TV/VCR.
Solution
If none of the TV/VCR combo codes work, you may need to set up separate TV and VCR codes
to operate your TV/VCR.
If none of the TV/VCR combo codes work, you may need to set up separate TV and VCR codes
to operate your TV/VCR.
Problem
I don’t get any picture and/or sound from my TV.
I don’t get any picture and/or sound from my TV.
Solution
Make sure all cables are connected properly and that all devices are powered on. Consult
related owners manuals for specific installation and operation instructions for each device.
Make sure all cables are connected properly and that all devices are powered on. Consult
related owners manuals for specific installation and operation instructions for each device.
TROUBLESHOOTING
y
x
x
y
x
x
y
x
x
Press and hold a mode key until the LED begins flashing.
Press SELECT. The LED will flash each of the three digits in the code. A pause separates
each digit. For example, three flashes represent the number 3, and a rapid flicker
represents 0, so a code of 103 will be shown as:
FLASH <pause> FLICKER <pause> FLASH FLASH FLASH
each digit. For example, three flashes represent the number 3, and a rapid flicker
represents 0, so a code of 103 will be shown as:
FLASH <pause> FLICKER <pause> FLASH FLASH FLASH
Count and record the sequence of flashes to determine the three-digit code.
b
c
d
Press and hold a mode key until the LED begins flashing.
Press POWER twice. The LED should flash rapidly and turn off.
Manually turn on all devices (TV, SAT, DVD, VCR). Test the master Power Control
function by pressing POWER. All the devices should turn off.
function by pressing POWER. All the devices should turn off.
13
b
c
d
MASTER POWER CONTROL
You can program your remote to turn all of your remote-controlled devices (TV, SAT, DVD, VCR) on and
off simultaneously when you press POWER. All devices must be in direct line of sight to ensure proper
operation. Perform the following steps to enable or disable master power control for all devices:
off simultaneously when you press POWER. All devices must be in direct line of sight to ensure proper
operation. Perform the following steps to enable or disable master power control for all devices: